Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
I'm currently evaluating different platforms, that run on the nrf52832 soc, like Nordic Semiconductors own firmware, as well as Zephyr, myNewt and mBed. As you guys from ...
Dear sirs
Good evening !
I´m using the RF24.h library in order to develop a system that comunicates in peer-to-peer mode.
When I transmit 3 bytes towards a receiver...
I'm hoping someone can tell me if I'm on the right track. Do I understand correctly that on an nrf51, the LPCOMP can be configured to wake the processor on an analog input...
Hello,
I was wondering how is calcualted or read on the Thingy firmware the variable w for the quaternion used in the Gyroscope readings.
Looking into m_motion.c in the...
The power data of lfclk is measured under the same hardware and software conditions. When we used two model chips, we found a difference of 1 microamps for the value of the...
hi, I am trying to make buttonless dfu working, but I am not sure how to do that. I am using SDK 14.2.0 with nrf52832. right now, the ble dfu example works. and I found in...
hi
i am using nrf52 dk with MPU 9255 as slave.which pin number of nrf52 dk should i use for 4 wire as SDA, ADO, SCL, NCS.In the attached file ,it is given as p0.20(MOSI...
I'm developing custom PCB with the nRF52832, and I would like to use the ITM for debugging. I don't have a J-trace or equivalent hardware, so everything will have to be done...
I was reading the tutorial :
https://devzone.nordicsemi.com/b/blog/posts/bluetooth-smart-and-the-nordics-softdevices-part-1
it says about how a ble device can advertise...
In Mesh SDK, there are 3 versions available for s132 softdevice: s132_3.1.0, s132_4.0.4, s132_5.0.0.
The question is, should I always use the latest version available? If...
Before I use 51822QFAC(with 32K RAM)， add I must use 51822QFAA(with 16K RAM)。
I have modify IRAM area，like this
IRAM: 0x20001FE8 0x2018.
and selete device is 51822QFAA...
We are designing the nrf52840 with high voltage mode and both DCDC regulators.
Where can I find the requirements for the external circuitry, like the inductors. For now...
Hi,
1. what the DC2DC switching frequency of nRF52832?
2. at nRF52840 the inductor should be 10uH with tolerance +-10% but for nRF52832 this inductor can be with tolerance...
Hey everyone,
I've been trying to get this basic bare-metal application to work. I don't need a softdevice as I'm just trying to turn on an LED. The application compiles...
Could not connect to the nRF52840 preview DK eval kit running the ble_peripheral/ble_app_uart firmware to iOS 11 device running the nRF connect or toolbox apps. We tried on...
