Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I plan on using the nRF51 Dongle meandered antenna for a design involving the nRF52810. Since the nRF52810 has an internal balun, does that mean that L1, L2, C5, C4, L3 and...
hi,
i have a custom board with nrf52832 as it's core. i want to program with st-link v2 programmer.
i am using sdk 14.2 and soft device s132 v5.0. on target location we...
Hi guys,
We have tested the mesh range in the nRF52840 chip (max tx power) in LOS and we got more than 200m.
W're planning to use the mesh network inside hangar with a...
I am still newbie in nRF52 dk . For my project , i am trying to send data from my sensor to the mobile phone through BLE App UART. Therefore first I have flash nRf52 with...
Hallo guys,
i tried some hours to receive the microphone and some other data from the Thingy 52 on an nrf52840 evaluation board and write it to an SD-Card.
Everything...
Chapter 43 of the OPS document for the nRF52840 says that the I2S interface has a "Low-jitter Master Clock generator" but I don't see a jitter spec for it.
What is the MCLK...
Hi every one I'm sitting with bluetooth mesh where I'm doing a project. where I get inspiration from "light demo" where I doubt how keeps each client / server control of the...
i am using redbear blend v2.0 where based on nrf52832, i try to execute ble_app_blinky examples code on nRF5_SDK_15.0.0_a53641a using uVision, but after i change some configuration...
I'm unable to get any example code to test the timer in counter mode, I see the data sheet and trying to enable, but its not working can any one suggest me how to start the...
Hello,
I believe there is a documentatin error in document nan_40.pdf CIRCUIT BOARD GUIDELINES FOR aQFN PACKAGE.
Table 3 / Page 11
Hole size of blind via is mentioned...
Hi, I have some questions about GPIO interrupt.
Now, I want to know the state of the pin, So I use the gpio_pin_read(PIN) to get the state. But when the pin is suspended...
hi,
i am working on a project were i have to discover all the service on peripheral device and fetch data from it like nrf connect app.
so i am using nrf52832 with sdk...
Hi team
I have a problem that bothers me for days.
I try to run demo ble_app_uart_c with
NRF_SDH_BLE_CENTRAL_LINK_COUNT=8 and NRF_SDH_BLE_PERIPHERAL_LINK_COUNT=1...
