Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
for the i2c_3 to work the following is needed to modify the SDK.
nrf/subsys/spm/Kconfig
```
config SPM_NRF_TWIM3_NS
bool "TWIM3 is Non-Secure"
default y
```
...
I was wondering the behavior of the NFC BLE Pairing with OOB when max connections are full. Will the connections disconnect in order to pair with a new central after an NFC...
Hello,
in nRF52832 devices, P0.21 pin can be configured as reset using PSELRESET[0], PSELRESET[1] ergisters.
Due to space constraints, i dont intend to use the reset...
Hi：
I want to ask：the nRF24L01 can work in single point mode by SPI commands。 I need the wave show like in the picture。
IF it can,which software and hadware I need....
Hi,
I trying to send indication supplied with some data to my Android app (which BTW works fine with other BLE devices) as an answer to characteristic write command
...
I am trying to run a project on a Fastnel
BT840 module
I had the code running on The dev kit when we switched to the new hardware without a FL crystal I have been unable...
Hi,
I am working on writing data on flash and reading it back.
i am not able to read data which i am writing to it . i am posting my flash file please suggest where i...
I need to sendt several indications on one BLE_GATTS_EVT_WRITE event. If I just call sd_ble_gatts_hvx I get NRF_ERROR_BUSY Isn't it strange? API stats:
Only one indication...
Hello,
I'm a beginner and I have lots of questions. So I wanna communication with MCP4110 chip. But I can't. I configured SS, MISO and CLK pin in sdk_config.h. (SEGGER...
Hi, all,
I try to use NRF52832 as central and peripheral. When it is connected with peer as central, I try to send to peer a message with "sd_ble_gattc_write", but I can...
Hello,
I have enabled WDT for nrf52810,S112 with following configuration.
static void System_task_initWatchdog(void) {
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Pause << WDT_CONFIG_HALT_Pos...
I'm using the nRF52 DK with SDK 15.3.0. At this point I'm trying to get a UART loop back to work by tying the TX pin (P0.8) to the RX pin (P0.9). I have verified that the...
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hi,
Good Day!
Problem: We have LED Screen connected to nrf52832 through SPI com and we have some led graphic effects in our application which requires some delay between...
