I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hello I am using SDK12.3 without softdevice on a custom board (with nrf51822 256k flash, 16kram without 32768 crystal).
I have written some code using GPIOTE to detect...
Dear support team,
I’m using nrf52840 with PCA10056 and SDK 14.1. I have problems of UART connection.
I do believe that MCU has physical connections to nrf52840...
Hi!
Now I am going to control the hardware flow and control the UART.
For that purpose, we send an RTS signal from the external MPU and the nRF 52832 that received it sends...
Dear team,
I bought a nRF52 DK which is labled "PCA10040 V1.2.1 2017.21 xxxxxxxxx".
xxxxxxxxx is a serial number, I guess.
I just could not run the most simple example...
a friendly hello to anyone interested in my question and setup
first i would like to explain the makefile setup, which works and 2nd i will go into the managed one and...
Hello !
I'm struggling with my Bluetooth configuration on the NRF52832. I'm running with the latest SDK (14) and the S132 SoftDevice.
When I'm trying to add a characteristic...
I am testing OTA DFU using NRF toolbox on Android. I have no problem updating my application using a zip file generated with nrfutil.
nrfutil.exe pkg generate --application...
Hi all,
I try to control IC by nRF52832.
[My Application]
・Supply 2.5V to nRF52832 and IC.
・Connect P0.10 to IRQ(IC)
[I did these setting]
・Define "CONFIG_NFCT_PINS_AS_GPIOS...
Hi all, I am porting my 100% working code from keil to use C++ and GCC and when I use the macro NFC_NDEF_MSG_DEF to initializate the NDEF message I receive the following message...
Not really a question - I have had trouble with J-Link RTT Viewer for some time, when it works it's a very useful tool, but it was only working about 25% of the time.
This...
Hello All,
We have One central device and four peripheral devices.
From every peripheral device we are transmitting battery level.
I want to change the peripheral or...
Hi team support,
Got a problem with project ANCS and more precisely with the bonding and the Flag "allow_repairing" which was false and set by myself to true. But on SDK14...
Hello,
I'm trying to enable the monitor debug mode work with iar but I have some doubts about the address used in the EnableMonMode.mac macro provided in one of the blog...
Hi all,
I'm using nRF Sniffer (2.0.0-1.beta), i didn't have any problem for follow connection between master and slave but now, I have a problem with time displayed in...
