we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
When I take a vanilla Objective C Xcode project and try to convert it to Cocoapods for an iOSDFULibrary with Xcode 9 results in an unopenable project. You get an error...
Hi,
I am using nrf52832 to scan beacons and then store temporary into two dimensional array.
I made interrupt that call after some interval to send stored beacons over...
Hello,
I got two device with DFU-OTA service enabled
(included device manager and dfu related handlers/files; merged the application, dual-bank bootloader, s130, app_valid_setting...
Using GCC compiler with Eclipse, sdk v14.1, nRF52832, in ESB protocol mode.
The code compiles and builds just fine, all links are ok, but the code below issues a syntax...
One of my nRF52-DK started to act oddly - very brief message in red type flashed up by nRFgoStudio on programming a few times - unfortunately too fast for me to read.
Now...
Hello,
I'm trying to build the ble_ant_app_hrm (multiprotocol) example, using SDK v14.1.0
Here is the output I get, after running make :
Makefile:216: Cannot find...
Is possible use the PPK with a custom board to measure the current usage?
In the pictures it looks like has headers to attach the nRFxxDK modules. but what about custom...
When configuring my Bluetooth Mesh server node to the network, it receives an error and I am not sure why.
I receive an ACCESS_STATUS_INVALID_MODEL error after having called...
Hi,
I am aware of how to use nRF51 sniffer with wireshark.
But in my current project, I am not able to sniff data packets. I am not sure which BLE stack is used in the...
Hi,
we have implemented the experimental_writeable_ndef_msg example from SDK12.2 with Nordic NRF52 on a custom board. Reading the NDEF Message works fine with smartphones...
Nordic nRF52832 chipset
Battery operation such as CR2477 Lithium Manganese primary button cell.
Many application circuits show this microcontroller used with a button...
Greetings,
One thing I've noticed is that if I enable the RTT nRF_Log messages in the bootloader, then the RTT messages that are being sent out in my application do not...
Hi,
i have recently bought a development kit for the nRF24LE1 chip. Untfortunately there was no CD included, as described in the following user guide.
data.icbank.com/...
The nRF51822 Bluetooth Smart Beacon Kit has P0.09 and P0.11 connected to the programming connector P2 (Pin 3 and Pin 6). From the User Guide :
Can I use them as UART...
I have a Rigado BMD-300 Evaluation Board with a BMD 301 module attached. Using the Texas Instruments SmartRF Packet Sniffer, I see the message being broadcast approximately...
