Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
is it possible to configure the nRF51822 Beacon (RCA20006), that it could be used as a wifi access nfc device.
So that the device (Beacon) sends the Wifi SSID and...
Where can I find a working application that has an observer callback function (not a beacon) .
this application must have also the broadcaster callback function.
OS: Ubuntu 14.04
IDE: Eclipse, installed as per tutorial.
Board: pca10040
When trying to debug esb prx and esb low power trx I get the following error:
No source...
So I'm only use to programing PICs with mplabX
I've designed my board and am ready to dive into programing the Nrf51822
I'm a little overwhelmed by the different information...
Hello,
I have build a gatt server device and my application is setup following the tutorials, which are really helpful by the way.
Now I want to check if the notifications...
I'm doing a more complex application than what I'm showing here, but I've reduced it to the minimum. I'm initializing the RTC subsystem, creating a timer, and starting that...
Hi all:
I use the softdevice 2.0.0 and compile bootloader example with "dual bank" on the nrf52 DK,
Running a system that can using DFU from app then jump to bootloader...
Hi ,
I search and found some of questions on this forum wich speak about enabling and disabling peripheral.
I'm ok with that but i have a question about there initialisation...
I am testing the Nordic nrf51822 chip.
I have rewritten a bootloader example allowing firmware updates via Bluetooth LE (FOTA). A mobile phone will sent the update package...
Hi,
I'd like to transfer some data from my App (using fstorage) to the bootloader (using pstorage).
Given that that the two storage mechanisms are different, how can...
Hello, I've been working on porting a bit-banged control of a peripheral to use nRF51 SPI--which is just SPI rather than SPIM (therefore no DMA). Observe the SPICLK waveform...
Hi guys,
I am developing a project where I have a large group of NRF52 chips together in one room. In their normal state each chip is paired as a BLE peripheral device...
We are working on a NRF52 DK. In the data sheet of NRF52832, there is no mention of enhanced shock burst mode or dynamic payload or multiceiver. Do I need to refer additional...
we're using Mbed for NRF51822. our board using 2 GPIOs interrupt.
problem: the Rise edge did not generate the Interrupt event: set EVENTS_PORT.
I try uisng while, but...
