I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
In table 32 on page 25 of the NRF51 Reference Manual, there are a bunch of registers with the description "Reserved for Nordic firmware design" or "Reserved or Nordic hardware...
Dear nordic.
I am testing with nRF51822, and have some question about hardware stability check.
nRF51822 have Clock Monitor Unit (Clock fault detector)?
Is WDT same...
I am running a standard schedule loop where I wake-up, service any scheduled tasks, then immediately go back to sleep. However, I am observing the following pattern:
...
Hi,
Everyone,
I have been working with Nordic NRF51422 with keil since laste 4 months.
Now I want to make Dev kit working on windows machine with eclipse GCC
Following...
Hi everyone,
When I run 4 instances (i.e., x2 PWM channels) of PWM with S210 (same example as the ant_background_scanning from SDK 10), after few seconds of constantly...
Hi, I am following the tutorial devzone.nordicsemi.com/.../ . to try to use eclipse to program and debug.
I have installed Eclipse on windows and I can compile without...
Timers are defined by a macro: APP_TIMER_DEF. This unfortunately expands to:
#define APP_TIMER_DEF(timer_id)
static app_timer_t timer_id##_data = { {0} };
static const...
Hi, we're working on a project that involves constant streaming of gyroscope and accelerometer data from an NRF51822 based module to a Linux machine.
What we've been working...
I am using the ble_uart_app on the dev kit with the nrf52. SDK version 11.0.0. How do I get the bsp_event_handler to get fired on a button release and button push event and...
Hi, I'm using stlink + openocd to flash and debug and it works fine.
But I want to measure the current consumption with nrf51822 debug interface off
Is there an equivalent...
I have a high-speed signal which I would like to sample with the nrf51's ADC. The signal is periodic (80kHz) and is from a low-impedance source (op amp buffer). I don't need...
I've been searched windows sample application for bluetooth.
I got android sample code but I need MFC sample code now.
If you have the sample code please let me know.
...
I've been playing around with the multi-central central/peripheral examples and I thought I would modify the peripheral to instead use a service I had written for another...
Hello,
If I supply 1.85V on the "External supply" pins, can i use all the modules of the board (nRF51DK)?
I need to have less than 2V on some of the pins as an output...
