Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello, I am using the NFR52 DK (s132) in peripheral mode. I have implemented a pairing mode based on a static passkey. However, the available time to enter the key in the...
Hi,
is it possible to atomically change both the GAP address and the advertising message in one step? I want to broadcast two different advertising messages with each of...
hi,
please any one explain me, what is the use of power registers of module such as UART, SPI, ADC,GPIOTE etc..
1.NRF_GPIOTE->POWER
2.NRF_ADC->POWER
3.NRF_UART0-...
Hi guys, now i have done the example as the light control demo description, but i have a question about that how i can let the light server to leave the network? Thank you...
A little background with this question
So, long story short:
To send data using notification, in android, you must first enable CCCD descriptor of matching attribute...
we have made 51822 communication with 24LU1+ successfully, result is 32payload, 2Mbps, 800FPS。
however, after add freeRTOS, our 2.4G will lost 5-8 packets and disconnected...
Hello,
I'm having a lot of trouble debugging some errors on UART. I'm initializing the UART as follows:
void uart_init()
{
ret_code_t err_code;
const app_uart_comm_params_t...
Hello Everyone,
I'm a beginner for nRF52 and my aim is to learn and develop system on nRF52. I have bought nRF52 development board and installed Keil MDK on my system....
I have to talk to a SPI device, which gets an address and then needs some time to handle the address. Afterwards the transfer can continue.
Is this scenario possible to...
timpwmadc.c
It is perfect (wonderfull!) idea to use programmable system PPI (EEP->TEP+FORK) alternative
PGA.
But I get some problems:
I tried to program a TIM3 to...
Hi,
Is it possible to call an arbitrary function at a breakpoint in gdb on the nRF52? I know you can with normal gdb, but I haven't been able to make it work with the cross...
Hi
I have a project to model the RSSI based indoor location using Bluetooth beacons. However, in order to do the basic distance and RSSI relation, I want to sense the channel...
Hi, im using nRF 52 DK. I interfaced mpu 6050 by using the example found here (BLE example found here is not working properly, dosent connect with uart app). I'm particularly...
Hi,
Does the erase target in the makefile completely erase the flash? I'm having strange errors when trying to read the flash (i.e. I can't read anything from flash, even...
