void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I am developing an application on a STM32 CPU that uses a 51822 through BLE serialization for BLE connectivity.
I have connected some LEDs at the pins of the 51822 to indicate...
Hi,
The nRF51WLCSP needs IR blocking coating and I found here that an example epoxy can be Epo-tek 320. I just want to check if there is any specific time for covering...
Hi
I have been able to successfully write using FDS but I'm unable to read back using the same keys. Here are my code snippets:
#define FILE_ID 0x1111
#define REC_START_ID...
Hello~
I'm using JLinkEXE to flash an nRF51822 chip. When I use nrfgo and press "erase all", it wroks. But after if I flash the s130, I can't erase the s130 with command...
Currently I have a few characteristics which are Authorized Read and Writes. Upon detected of the Authorization from the Central I trigger a few events such as:
Measure...
Hi !
I'm using an nRF52 on PCA10040 board and nRF5_SDK_11.0.0_89a8197. I want to run the peripheral ble_app_template with SEGGER Embedded Studio v2.20. I correctly set...
In an effort to try and determine why FreeRTOS tickles idle is consuming more current than tick mode with an idle task, see this post devzone.nordicsemi.com/.../ , I noticed...
Hi, i am designing a board using nrf51822 and planning to use a MOSFET for reverse battery protection instead of a schottky diode or a normal diode. I am new to this and learning...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I'm developing a nRF52 application that exploits two ADC channels in single ended configuration.
VDD is 3.0V.
For the signal conditioning I've chosen a driving Op...
I've been trying to get my head around using a BLE central and making connections so I've loaded up the multi-central example to figure out just how everything works. I turned...
Hi everybody!
I am working with ANCS (nrf51822 SDK 9.0) I am confusing on setting the connection parameters which are MIN an MAX connection interval.
Firstly, I set...
Hello,
I have some characteristics on my device that are containing some configuration data.
Every single variable is a global variable.
The values can also be changed...
