Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hi Nordic,
I was reading the Wiki page for porting OpenThread to a new hardware platform ( github.com/.../Porting-Guide) and I noticed there isn't a "flash.h" header file...
MIN_CONN_INTERVAL
MAX_CONN_INTERVAL
SLAVE_LATENCY
CONN_SUP_TIMEOUT
Hey guys,
I want use my device with Android as well as iOS, but i am facing some issues for...
Hello, when reading the source code for a mesh node provisionee, I stumbled upon this MACRO function:
NRF_MESH_ASSERT
Edit: it is in ble_mesh_v0.9.1-Alpha\mesh\src...
hello,
i am experiencing issues with the TWI library on the smart beacon kit rev. 1.3.0 which features the v3 of the nRF51822. i had the same experience on the new nRF52840...
Hi. I'm trying to flash Secure DFU bootloader together with my application. I tried to flash bootloader and then main application, but the device stays in bootloader instead...
ppi.zip Hi, I am using radio with ppi to advertize packets as shown in the mainc file attached. Even after allocating the access address of Bluetooth on line 196 as set_address0...
Hi there,
I am trying to measure environment below 0 C but the app reboots and refuse to connect with thingy52 at lower temperatures. Do I have to set up anything else...
hi ,
I have a question about rtc.In my project ,I use rtc1 for app timer and rct0 for low_power_pwm.The problem is that I dont't have any idear to enable rtc0 instead of...
hello:
i meet some trouble,i can find the service,then appear error "BLE_GATT_STATUS:10a".
#define BLE_GATT_STATUS_ATTERR_ATTRIBUTE_NOT_FOUND 0x010A /**< ATT Error: Used...
Hi,
I am trying to use the nRF51DK (PCA10028 v.1.2.2).
I cannot get Windows 7 to recognize it via USB reliably. I have JLink v6.16a installed and when I plug in the board...
I have variable values coming out of a terminal at all the time. I using this command:
void in_pin_handler(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
...
Hi All,
I am developing a ble applications and am unable to get pins 9 or 10 to work as gpio. I understand that this is because, by default they are used by the NFC.
...
How do I limit the number of peers that are stored in the peer manager? I don't see a configuration variable. I don't know the addresses of peers before hand, so I don't think...
