I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
From document [Getting started with the nRF52840 Preview Development Kit]
( www.nordicsemi.com/.../Getting-started-with-the-nRF52840-Preview-Development-Kit)
we know that...
Hi,
I'm looking for a BLE device to work with an arduino and to speak with a smartphone.
The point is that the connection should be made by the user via the smartphone...
I am using nrf52 with sdk11. I have set the advertiser data as Manufacturer data in nrfConnect app in my android phone. So that whenever the data from my phone is advertised...
Hi.
I try run "ble_app_hids_mouse" example from nRF5_SDK_11.0.0 in nrf51422 (nrf51 dongle).
Previously i ran this example in nrf52 (nrf52 DK, s132 SoftDevice), and all worked...
Hello!
We use chip nrf52832(QFN-48) in our project and we wont to pass the PCB certification.
But we also want to use chip nrf52810(QFN-48) in another project, but with...
Hi ,
Please advise, what the Low Power option I have if I want to sample Two channels of analog input at the same time. The sample rate in every channel is 12K, 12Bit....
Hi I am using SDK12.2.0 and Softdevice S130 v2.0.1 on board PCA100028 ; the board works fine and Phone can scan the name of DFUtarg； But when run the same on the customer...
Hello, I'm planning to try the NordicBlog; Capacitive Touch on the nRF52 series to test a button type or a up-down slider type .
I'm planning to use an nRF52832-QFAA for...
Hello,
Can you please provide any link or give me any advice how to connect NRF51822 chip with NRF51DK?
Here is my connection that doesnt work:
DK GND DETECT and GND...
float f = 1.234;
NRF_LOG_INFO("My float number" NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(f)));
How to simplify this way to show float number by uart in sdk13.1.
In...
I have 2 questions regarding BLE5 on nRF52832
Which Soft device and SDK has to be used to implement BLE 5 on nRF52832? We will be using the nRf52 DK for same.
Is the provision...
Hi,
I am using timer interrupt in my code. In that I will be generating interrupt after certain time interval, after the interrupt it should process the incoming data from...
Hi
We are using the nRF52840 and the application is OK now. Then I do the OTA using a Android phone which supports Bluetooth 5 and it's made in our country. I use the nRF...
