I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
When I test the timer example with nrf52832 DK, it so nice to 4 minutes.
uint32_t time_ms = 240000;
But when I set the time interval over 5 minutes, then the event...
What is the maximum number of bond table entries a device can have?
If a device allows only one connection to be established at once (not more than one simultaneously)...
Hi,
I want to store the CRC of the current firmware in the flash, for DFU purposes. Almost all of the threads I've seen so far reference the pstorage API but it's no longer...
I am searching for a basic example to understand the build system.
How do I load the soft device properly?
How do I set things up to run SEGGER_RTT_WriteString?
I...
I am using Nrf52832 sdk 11.I want to update the value of characteristic on every read operation from my andriod phone. I want that on every ble_gatts_evt_read: should give...
Hi! Im trying to figure out the power consumption of two types of beacons that uses nRF51 and nRF52. I have connected a small resistor in between the supply and measuring...
Preferrably under linux using gcc and the command prompt.
I am most interested in project setup, loading the soft device, and making sure all the core systems are working...
I am running the ble_app_uart example in SDK 13.0 with nRF52382.
First issue
The app can receive data via UART only when I use "Termite" as a terminal emulator...
Hi, trying to implement timeslot api and stuck with TIMER0.
I saw similar questions but answers is still unclear.
My timer init code:
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;...
Hi
I am using nrf52832 with softdevice s132_nrf52_3.0.0.
In my appliocation I need to do periodic measuremets, and it is critical that softdevice doesn't interrupt during...
Hi,
I have to make a interrupt each 100us. This interrupt should be priority on the BLE. In my interrupt I have only one condition (if/else) and I have to change PWM value...
Hello,
I'm looking to implement the OTA on my nRF52, but I couldn't find any help online.
I would like to do it with my iOS and my Android app.
Does anyone have a tutorial...
Soon we will start production and this is my first time using a Nordic chip. During production I want to test for output power en center frequency with a development kit as...
I'm trying to create a connection between Android 6.0 and nRF52832. I created a service, like in tutorial, added it's uuid to adv packet (I seeit in nRF Connection). I can...
