SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
today simple test ble_nus_string_send time-consuming function, but found that the implementation of a ble_nus_string_send and wait for the success of transmission time-consuming...
Hi, I have a problem with BLE connection. When I bond to the device and then connect, everything works and connection is stable. When I kill the app and try to connect again...
Hai team,
Iam using ble_app_beacon application in nrF51822 dongle .I want to change tx power for every advertising.
example :let us assume frequency 4 for advertising...
I am trying to perform LESC on two nRF52 central and peripheral without bonding is it possible? and how?
My devices does not have I/O capabilities or have any display....
Most examples, tutorials, and standard BLE service implementations within the SDK (14.1.0) seem to use the BLE SoftDevice's sd_ble_gatts_characteristic_add() when adding a...
Hi,
I know that this question has been asked before but it seems like the answers are pretty old.
I have a need to scan on one channel only to receive advertisements...
Hi,
As mentioned in this post:
devzone.nordicsemi.com/.../
the struct ble_gap_adv_params_t --> ble_gap_adv_ch_mask_t give the option to turn any advertising channel...
I'm calling sd_ble_uuid_decode with the following parameters on a PCA10040 board:
sd_ble_uuid_decode(16, 0x2000F7CC, 0x2000F7DC)
ram base = 0x20003150
vs_uuid_count...
I want to use in my project tft 1.8 display with st7735 controller. I used the standard GFX example from SDK 14.1 and everything is working fine, but the picture is incorrectly...
I have a QFN48 nRF52832, and it's getting hot. I'm looking at it with a thermal camera and there's a hot spot directly under the "N" of the "N52832" that's on the package...
The BLE_NUS_C_EVT_DISCONNECTED of the ble_nus_c_evt_handler() give a conn_handle = BLE_CONN_HANDLE_INVALID . So it's not possible to know which peripheral got disconnected...
Hi everyone !!
I'm a beginner in ble mesh. I'm working with nRF 52840. I'm not being able to figure out how to see log messages. I want to know where will following line...
Is there anywhere I can find some high level documentation on the FDS module? I'm going thru the API documentation but it provides very little insight into how to best setup...
Hi Nordic Devzone,
First i want to make sure that if the clock being used by softdevice is the LFCLK (32kHz) and its counter register is 24bits ? and which prescaler is...
