Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I got this error when trying to use the button library to debounce noisy buttons.
My application is a peripheral.
When I looked in the library source I saw
#if NRF_MODULE_ENABLED...
I am working on a nRF52328 present in the Taiyo Yuden EYSHJNZXZ module. I am using an FTDI module for UART communication. I followed the steps in the following tutorial: link...
Hi everyone I'm Rookie....
Recently bought this board, want to do more applications in the expansion of the pin,
for example, control stepper motor or LED, but can not...
I am using the experimental_app_hrs_nfc_pairing_pca10040_s132 nrf52 example.
I want to set my custom uuid and I have followed the instructions given in the devzone.nordicsemi...
HEllo I am having an error saying
Undefined reference to
SEGGER_RTT_printf
I have looked into this post and tried it, however I am not able to fix it,I have defined...
nRF5_SDK_12.2.0.
app_timer_freertos.c
app_timer_stop() call xTimerStop/xTimerStopFromISR with timer_id parameter.
It seem to must use hTimer parameter.
It's bug?
MY application is using SDK 12.2, SD132 v3.1 and freeRTOS. I'm trying to debug a sensor that uses TWI. When I enable logging. #define NRF_LOG_ENABLED 1, NRF_LOG_BACKEND_SERIAL_USES_UART...
Hello Everyone,
I am new to keil and nrf51822 programming.
Currently I am using softdevice s130 with hex file for bootloader from
folder : nRF5_SDK_11.0.0_89a8197\examples...
Hello,
I would like to instruct my application to read the battery voltage on my nRF52pca1040 DK, I am intending to do so through the SADC.
I will feed the board with...
Hi,I have some problems in debug with experimental_ble_app_buttomless_dfu project.
First i build the experimental_ble_app_buttomless_dfu project,so i get the app_buttomless...
We am improvising nrf blinky application, we have got stuck in a problem, after button is pressed from nrf52-dk code goes into forever loop and after a while connection is...
I have two nrf51822 modules and first one is sdk8.0.0 / s110 / peripheral device, second one is sdk10.0.0 / s130 / central device. I've sent a 10-character data array like...
Using:
SDK14
Softdevice132 V5.00
app_uart driver with legacy, no easy dma.
UART is set up with hardware flow control.
The pins should be set up correctly: rx-tx , cts...
i want to konw ble evt struct 's content of meannig . i want to find what's the return value when packet send fail and what is the channel id different from other ruturn value...
Hello,
I want to falsh nrf51422 device. I ma developing software using Eclipse and SDK_7.2.0.
The soft device is 130. I have build the project successfully and Hex/elf...
