i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I'm using the original BLE App UART from nRF5_SDK_14.0.0 on a PCA10056 Board.
The board is advertising, but if I want to open a BLE peer-to-peer connection, than the application...
With SDK 14.0.0 and Softdevice 5.0.0 I have problem with Windows 10 connection. The device connects to PC but then almost immediately disconnects with reason 0x13 (BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION...
Hello,
We developed a few devices using the nRF51822 and noticed that the receiving range is reduced significantly from our nRF24L01 devices. The transmission range is good...
Hello,
I'm trying to measure the current profile with the PPK (HW Rev:1.1.0, SW: 1.1.0) but I see a lot of strange behaviors.
My firmware initializes everything and the...
I am running a nrf52840 dev board as an NCP connected to a RASPBERRY Pi running wpantund.
I have 10 other nrf52840 devices in the network. The PI has LIBCOAP coap-client...
Hi,
Just curious to know if anyone else had this issue and how they solved it.
My colleagues and I are working on code based on the Nordic Uart Service, in SDK13.1.0...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I am using 3 uarts for my applications using nrf52xx, i want uart without fifo,i configure 3 uarts independently and use the
#define APP_UART_INIT(
P_COMM_PARAMS,
EVT_HANDLER...
Hi Nordic forum.
We wanted to update the bootloader over the air. Initially, we had a very plain bootloader (the one provided in the example) but later we added a timer...
Hello everybody.
Please answer my question.
I repeated the Bluetooth pairing ON → OFF of my smartphone and DK 52
(PCA 10040 + HRM) and checked the connection, I encountered...
Hi
I'm trying to use pstorage to save some info (device name, and user info).
I've found the following links with examples:
infocenter.nordicsemi.com/index.jsp
devzone...
Should these beacons be advertising as bought off-the-shelf? I've got six and was expecting to be able to pick up their advertisements but I'm getting nothing.
In this application, I tried to enter a wrong bonding passkey to test PM_EVT_CONN_SEC_FAILED case. But I found that the program went into this case and after executed "sd_ble_gap_disconnect...
