Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
The absolute max throughput for the nRF52 using S132 v2 was 128 kbps .
The new S132 v3 was recently released and boasts throughput increases by 400%. Has anyone tested...
I am trying to send small data packets of up to 9 bytes at the fastest and most consistent rate from a nRF52 peripheral to a nRF52 Central. Both use the s332 SoftDevices....
Hello !
I've created an app based on the nrf blinky master : it works perfectly on my smartphones.
But when I kill the app, and when I relaunch it, it doesn't connect...
Hi,
I am trying to use a mux change among 3 differential channels. The diff signal then goes through an instrumentation amplifier. The steps I'm using:
switch to ch1...
Occasionally, when trying to program a softdevice in nrfgo studio, it can't find the softdevice hex file. It was there during the last several programming sessions, but now...
I would like to achieve in the room inside a number of devices to achieve one-to-one binding 8K / S unidirectional transmission of data, is not the use of proprietary_rf inside...
Hi,
I have set up a two NRF51DKs one in a central and one in a peripheral role. Using MCP and nRFConnect I have confirmed that I can send read requests to my peripheral...
Hi,
the documentation page of Gazell warns that it is outdated.
Warning: This is old documentation, and should only be used for historic reference. Please go here...
Hello,
can you help me with choosing the right software components for nRF51 and nRF52 ?
nRF51 on the left hand side works on the battery and turns on when the button...
hi,
I am working on nrf52 sdk11 and s132,
when I am using ble_app_uart example on my custom board I used nrf_delay_ms(10000) i.e 10 seconds when i observe current consumption...
When i use sd_ble_gatts_hvx() send package,i can use the usb dongle get the data package,as it show i can get the information such as, LLID, MESN, SN,MD,PDU-Length show in...
Hello,
I am trying to scan a local name for beacon device on nrf51822 SDK12.0.0 ble_app_multilink_central. The original peripheral sample was working as well. But the beacon...
I am using SDK 12.0.0 and Nrf51 ship.I was trying to compile micro-ecc library in eclipse using make file.I have cloned the micro ecc library from this link .I am using the...
Hi,
I want to eraze the flash page of nrf52832.
Since the default flash page size is 4096 bytes, it takes 90ms to eraze the page.
I want to shorten the time for erazing...
Hi!
I have to do an application is talk via bluetooth. I think i use codec IC to sample the voice then send data via bluetooth. In the receiver device , I use other codec...
