I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I would like to setup the just released RasPI demo using the Nordic-Thingy52-Nodejs repo
I don't have a dongle, but 4 PDK 52840 boards and 2 Thingys.
Can I still use 1...
I found that blindly configuring all GPIO pins can stop the LFXO and RTC counter. I am reporting this as: something to be aware of, not obvious to everyone. Not a question...
I am testing the nRF52832 in Rigado BMD-301 module. I am able to get to ~40uA when advertising ,UART enabled but not used and all other peripherals disabled. But as soon as...
I connect to my BLE peripheral device using NRF connect app. While in connection, if I switch my phone's bluetooth off and turn it back again and then try to connect to my...
Hi!
I'm using the nrf52 on custom prototype boards and the official development boards. We are using the ADC to read analog values and encountered unexpected behavior related...
Starting notification and then writing 0x01 to the control point
does not cause the Buttonless DFU to enter boot mode. LED #1
remains on.
Run time trace show:
APP...
The Problem ist the continuous sending of Byte-Arrays with spi and fixed sample rate.
Strategie:
Send Array-List with XFER triggered by Timer (every 3ms) and auto increment...
Hello,
I bought Nrf 52832 breakout board .
Actually i want to measure the current consumption of chip as we want to use it.
While advertising 26 bytes it consume really...
I have questions about the HCI packet format
With the start packet, the Ack number in the header section = 000
What should it be filled in the data packet and...
I'm implementing an I2C communication and I need to set an interruption every time the sensor sets the interrupt pin to 0. I've been checking some other posts from devzone...
Hello,
I am currently trying to power profile all aspects of the nRF52840, which includes the CryptoCell 310. The instructions say "
Testing
Test the CryptoCell Example...
I tried to use Timer2 as counter with event and interrupt. event is working. interrupt not.
<pre><code>
timer_count_cfg.mode = NRF_TIMER_MODE_COUNTER;
err_code = nrf_drv_timer_init...
s132_nrf52_5.0.0-3.alpha_softdevice.hex (/attachment/26a9916e1af8c97bcba7185035bd7b31)Hi, I am starting to work on NFC and Bluetooth pairing for the nrf52 and i tried to compile...
