When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hello,
Is the characteristic value data supplied to sd_ble_gatts_characteristic_add() and sd_ble_gatts_value_set() copied into the softdevice RAM, or does the softdevice...
.pdf d051cefddbc197cd7d)
Hello All,
I am working on Automotive project using nrf51824 SOC...
Hi,
I am working on making a test harness using the nRF52DK and a raspberry pi so I may run unit tests directly on the nRF52832. I want to use the UART to give test results...
We recently did pre-compliance RF radiated immunity testing at a certified lab. The EUT was nRF52832 on a battery powered post card sized circuit board with some sensors....
when I run the program I get this error
Checking installed packages
pyside: 1.2.2
pyqtgraph: 0.10.0
numpy: 1.11.3
pynrfjprog: 9.1.0
Warning: The software is tested...
I am using a PPK with v1.0.0, but elsewhere in DevZone I see references to later versions of the software. Where can I download the later versions from? Have I missed a link...
Hi.
Great that you have added logging capability to the PPK desktop app. This was exactly what I needed.
I noticed one minor issue with the logging: When starting logging...
I have an application with hard real-time requirements (i.e. down to the clock cycle). My topology and desired timeline can be seen below. Concerning the timeline, I believe...
Hello,
I have a question regarding app interrupt handling.
When an Application Timer Interrupt is being handled, can it preempted by a higher prioritized interrupt of...
Hi,
I have used this antenna for my nRF51 layout, but it seems that the device is using very high currents! like in order of 200mA, I just wanted to know if this is because...
I am using below code to send data over nus. If the data size is 150 bytes, it is OK. However, if the data size is 200 bytes, the nRF51822 will reset. Please tell me how to...
Hello, I got problem in enabling whitelist on starting advertising.
My working enviroment is PCA10028 V1.1.0 2015'18, SoftDevice S130 2.0.1, SDK 12.2.0
MCP works on Android...
Hello,
We encounter the problem after upgraded the PPK software. There are different results when using PPK v1.0.0 and v1.1.0.
Using PPK v1.0.0
Using...
Hi,
There are similar questions posted, but none of them have able to help me out.
I am trying to add multiple base UUIDs in order to create 128-bit UUIDs for my characteristics...
how to create custom service in order to send dummy message, not from the console, I
have to make one char arr[]="hello" this is a fixed string, then where i have add this...
