Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
I connected up +5v to the external power pins of the nRF52dk. I see +5 at TP14.
When I set the power switch to 'on', the board does not boot.
Is there something else...
Hi:
Looking in both SDK12/13 I cannot see any examples related to an HID Joystick/Gamepad.
It looks like somebody asked a similar question here: devzone.nordicsemi.com...
I am using nrf51822(pca10028)
i used the timeslot API tutorial in devzone..and it worked fine but i want to integrate the radio receiver example along with this.
nrf_radio_signal_callback_return_param_t...
Hi
In the SDK13 release notes and even in a few posts in the DevZone the new S140 5.0.0 Alpha2 Release is mentioned. I looked for the download link in the product page...
Hi all
I'm using the GATT server on the nRF51822 with the SoftDevice S130 V2.0.1. I've implemented a service and a characteristic which supports only write requests (including...
Here is my question.
I always disable uart after I send data.
NRF_UART0->TASKS_STOPTX = 1;
NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
this was write in the...
Is there a compiler/makefile flag that allows for 64bit printing?
I have included inttypes.h, and tried both %llu and "PRI64" as shown:
char scrbuf[30];
uint64_t time_alive...
Hi
We are using NRF52 and SDK 11 and S132.
The nrf52 acts as a central and selectively connects to the closest phones (ios) that are acting as a pheripheral.
For this...
hello,
nordic's engineers, need your help.
(1) the first problem : can not set VDD output to 3.3V
From nRF52840_Product_Specification_v0.5, it says:
High voltage mode...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Hi. I'm using nRF51822, SDK12.2.0, S130 v2.0.1.
I'm using nRF chip as Multi-connection Central and 1 Peripheral as well.
My event function is
static void on_ble_evt...
I've tried everything I can find on this topic and I still cannot get P0.09 to behave as a GPIO pin. Does it have something to do with the way I'm attempting to initialize...
Hello,
I am working on a custom PCB with a nRF52832 and I've been unable to get the ON IDLE power under 480uA. Here are the basics regarding the setup
nRF52832 Rev...
Hello! I'd like to know if S132 v3 implements the frequency hopping scheme defined by BLE.
I've read some documentation on Gazell, but from what I understood, that is a...
