We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I tryed to port the dfu secure bootloader sample of sdk 13 to eclipse managed project. after a few hours, i finished it. compiling and linking went fine but the filesize is...
Cannot connect to ATECC508A through TWI with NRF52832. Tested with nRF5_SDK_12 twi_master and deprecated twi_sw_master. It was working fine only with NRF51822 nRF5_SDK_12...
Can nRF51422 or nRF51822 can be used as bluetooth device for Raspberry pi?
As I can see on the terminal Linux, the hciconfig log says, raspberry pi 3's Bluetooth device...
Hi,
I recently migrated our code to the SDK 13 (we use the nrf52832) and now the function:
uint32_t err_code = ble_radio_notification_init(6, NRF_RADIO_NOTIFICATION_DISTANCE_5500US...
Hi,
I can't discover more than 5 characteristics on central with SD130 2.0.0.
I have trided nRF Connect and characteristics were discovered successfuly.
Is there some limit...
Hi,
I have a situation as below.
I have the list of host addresses (public type). Based on the command received, BLE peripheral device should advertise in direct advertising...
Hello there,
We are using nRF52832 custom board. I2C and GPIO are working on it. Then I uploaded BLE program (which is tested on nRF52-DK) but BLE is not showing up at...
Hey Guys,
I noticed when I use nrfutil DFU BLE command on the nRF52 DK the nrfutil program a "connectivity firmware" before the perform the DFU BLE to a Target device....
hai
i have tried to store and update some data in flash using pstorage. on storing data data is stored successfully.
#include "mbed.h"
#include "pstorage.h"
#include...
Hi all ,
hi NORDIC team ,
I'm currently developping a multiprotocol adapter LORA/BLE . I'm using the sd130 .
Semtech's third party says that it's "recommended " to have...
52832，SDK12.0.0
I met such a situation:
In the use of JLink burning program or air upgrade, after the completion of the program card died in initialization low-frequency...
If I am programming a BLE Server device, and I configure a characteristic with BLE_GATTS_VLOC_USER and queue a notification with sd_ble_gatts_hvx(), how soon can I update...
We're developing with SDK 10.0, nrf51, softdevice 8.0.0, s110.
We started with the ble_uart_app and added our own functionality, which includes the timeslot functionality...
the code is
nrfjprog -f nrf52 --snr --memwr 0x10001080 --val 0xabcd0102
I am doing the example infocenter.nordicsemi.com/index.jsp
I am able to get everything up to...
Hi,
I am currently going through the GCC and Eclipse tutorial. Now I struggle to compile the project.
I installed the blinky project (nRF5_SDK_11.0.0_blinky_blank_pca10040...
