I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hello, I am new to NRF. and actually i dont have other MCU experience, beside adrduino.
my question is not about BLE/BLE+,
it's more about how to use NRF5283 in keil question...
SDK 13 Alpha
The header guard in serialization/connectivity/codecs/s132_s140/serializers/ble_l2cap_conn.h looks like this:
#ifndef BLE_L2CAP_CONN_H__
#define BLE_L2CAP_CON__H__...
Hello,
I really like the new nRF52840, especially it's Bluetooth 5 capabilities. The thing is that i cannot figure out if i would be able to make nRF52840 based devices...
Hello,
I have tried to debug ble_app_uart_pca10040_s132 application included in nordic SDK12.2 with Segger Embedded studio v3.12, but even though I don't get error while...
I have been working on an application for iOS for a few months now, and I want to give my users the best experience possible, when it comes to the peripheral I intend to use...
I would like to test the Fatfs demo using a target spi flash memory chip. The example code calls out sd card fatfs driver. Can I assume that spi flash memory is the same as...
I'm building a software for the nrf5822 using pc10028. I'm using CMake and after following both morf.lv/modules.php and devzone.nordicsemi.com/.../ I successfully made the...
Hello Noridc,
Liking your solutions, and I appreciate the thorough documentation.
Working on layout and so I was looking carefully at your reference design Gerbers for...
Peer manager worked fine for bonding on my pca10040 board. However, when I flashed the code to my prototype, built with a SparkFun nrf52832 prototype board, I received PM_EVT_ERROR_UNEXPECTED...
Hi team,
Iam using sdk12.1.0(ble_app_beacon and ble_app_hrs_c) , i modified the advertising data and sending to other end.other end one scanner is receiving the data .but...
Hi,
i am beginner to Nordic i want to work with MMA8652FCR1 using NRF52 DK board is there any example to understand What is TWI and How to work with it. and also how i can...
Hello to all embedded Jedi Knights!
I was wondering, how could I read the CTRL-AP's APPROTECTSTATUS register (of an nrf52832) using the J-Link commander.
I know that...
What are the states of the bi-color LED (LD5) on the DK?
I'm aware that solid green is enumerated and 10Hz blinking is not enumerated (or power-only). Do the other states...
