Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I am trying to design a power supply circuit for my project based around the nRF52 and various sensors. I need to use the 5V pin so I will need a bigger battery...
Hi,
I would like to estimate power consumption in central(master) mode. However, power profiler in devzone.nordicsemi.com/.../ only provides power consumption in peripheral...
We're encountering a frequent but intermittent hang after handing off OTA DFU to iOSDFULibrary 3.1.0. In the happy case, the characteristics are discovered and DFU process...
We are using the Android nRF toolbox v2.4.0 and have successfully implemented the Template app. The app will reliably connect with our device and functions well. The only...
Hey,
I was on one of the meetups when nrf52 was presented. You guys used a mbed shield for demos. Do you have code example and what pins you were using for connection?
I am working with the PCA10028 board, SDK 10.0.0, and s110 8.0.0. I have created a characteristic that is "coupled" to LED2. When a connected central writes a value to the...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hi, All!
I am using nRF51822QFAA with 16KB ram, and S130(sdk 11) for the dual bank bootloader, reference to the s130 releasenote, I config the ram memory start at 0x200013d0...
Hi,
I have tested several BLE examples in SDK12.30 and they would not compile, what's the problem?
for example here is the output of ble_app_uart example.
*** Using...
Hi,
Using this doc it says the SPI supports 16 bit frames. Is this true for the nrF51822 BLE Nano? I found that the mbed API does not support 16 bit frames doc . Can I...
Hello,
I tryed to find in Q&A something that can help me understand how it is possible to measure battery voltage with nRF52, but i am not sure i found the exact explanations...
The v3 reference manual of the nrf51 mentions:
"[The powerfail comparator] also provides hardware protection of data stored in program memory by preventing write instructions...
If I use the interrupt handler to set Flag, and read sensors and write data to SD card in the main loop as in the following code then everything works well.
#include <Wire...
