Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I have followed the CoAP example from IoT SDK,
I have a Raspberry PI set up as the router,
and two nRF52 boards, one is the client, the other is the server.
Following...
I have following questions:
Is there an example for implementing WeChat on a nRF52?
Is the nRF52 module supported for WeChat AirSync?
Where can i finde the requirements...
Hello!
I'm drawing a circuit with nrf52840 chip and I want to ask some questions:
Is it ok to use 2-side pcb (not 4)? what's of these better in part of radio communication...
Hi, I use nrf connect to programing demo board nrf51 dongle to get it work, failed.
error log as follows:
2017-03-02T09:30:20.014Z INFO Application data folder: C:\Users...
Hi,
Does the PPI module automatically clear the event flags for the linked event? For example, if I have the following:
NRF_PPI->CH[0].EEP = (uint32_t)&(NRF_GPIOTE->EVENTS_IN...
hi
I'm porting Arduino code which has calls to ShiftIn() to read a byte from a GPIO Pin and bitWrite() to write a bit into a byte variable at a particular position.
Below...
dear friends,
now i need to let a master 52832 device communicate with multiple slave 52832s.how can i make it? Our scenario is that a teacher takes a phone in a classroom...
I used SDK12.2.0 and S130 develop with 51422;
I want to test for fds write and read, I followed the fds_sample from github; it can write success, but no FDS_EVT_WRITE return...
I have to exchange information with smart cellphone. My 10040 board create a pair of key by micro-ecc and transfer the public key to the cellphone. However, the cellphone...
i am using timer 1 of nrf24le1.for which i have calculated a value which is to be loaded in th1 and tl1 for 1ms .calculations are as,
clock =16mhz;fosc=16mhz/12=1.333mhz;t...
Hey everybody, I'm having 'intermittent' issues with device addresses on the nRF24L01+. I've read the documentation on what you're not supposed to do as far as device addressing...
dear friends,
There is a pic that i catched using sniffer. SlaveLatency,a gap parameter,is set to 2.As you can see, when the slave do not give an ack,the mater will resend...
Hi
I am measuring the current.
I use SDK 12.2.0 , NRF52 and S132.
I noticed that current was flowing even while device waits events.
Device waits by sd_app_evt_wait...
Is there a way to receive/send messages from/to the nRF51822 (I am using the BLE nano from redbearlab) with a java desktop application? Is there any java library out there...
