Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am interested in optimising inputs for ADC measurement on an nRF52.
I have seen quite a bit about nRF51 but am unsure if this remains relevant for nRF52?
Hi!
I have an nRF52832 on a custom board. I managed to flash it through JLink and STLinkv2. But suddenly, I wasn't able to communicate to it anymore.
Openocd tells me...
Hi
The new signed DFU in the SDK12.1 comes along with a experimental buttonless DFU. There are a few bugfixes required to make it working, but the nRF Toolbox app didn...
Hi:
Recently, I want to use nRF52 to read or write some data from a flash chip(w25q128bv) by using spi, I've read Manufactures ID correctly, also, I have wrote a register...
Hello!
I need to interact with two J-Link debuggers, connected to the same PC at the same time. I would then read and write data to the devices connected to the debuggers...
Hi team,
iam using sdk 12.1.0 (ble_app_beacon) I want to advertise the battery percentage.Right now iam using the nrf dongle(it doesn't have cell coin battery) and flashing...
I am attempting to build some ptorotype code using SDK 12.2.0 and GCC and I just added calls to the app_schedukler library and to the saadc driver. I added the relevant source...
I always read 0 first time I call sd_ble_gatts_value_get(), the second time and forward I read correct value. Even if I call sd_ble_gatts_value_get() twice in a row the first...
Hello,
I generated a new project using the main.c of the example "ble_app_uart" from the SKD 12.2 for a nrf52832 and from there copying all necessary .h and .c-files into...
Hi DevZone
I am trying to DFU OTA a PCA10040 using BLE Secure DFU Bootloader from SDK12.2.0.
I can succesfully transfer the image i have made with nrfutil to my DK,...
Hi,
I'm working on integrating ANCS on our existing and futur products. I started to port the Nordic SDK example (12.x) and it seems to work fine on nRF52, which will be...
I am currently using SDK 12.1.0 and experiencing intermittent HardFault crashes in timer_list_remove() with the stack indicating the origin being a SWI0_IRQHandler call. ...
i have a setup with one NRF24L01+ as PTX and one NRF51822 as PRX
my problem is that the data sended ok and ack sended to NRF24L01+(i assume that by NRF_ESB_EVENT_TX_SUCCESS...
