Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
hi, i have a SIM800L Core board which is using UART protocol to communicate or to send At commands. so that i am using BLE_APP_UART example to set AT commands to SIM800L....
Trying to follow this tutorial using KEIL 5.23, J-Link 6.14b and the DK.
I am getting linking errors like this when compiling:
What did I do wrong and how can I fix...
hi,
i was looking for example of two nrf52 communication. One is central of course and other one is peripheral. But i have following doubts.
If one is central then...
What is the right way of stopping and then subsequently re-starting SAADC?
Using the saadc example, I want to be able to stop saadc when a certain pin is grounded or when...
Hi,
I just found the following example:
infocenter.nordicsemi.com/index.jsp
There the baudrate 115200 is set by default. If I calculate the bit rate (8 data bits one...
Hello,
I use two NRF24LE1 emission and reception when I use a simple ACK is good but with ACK payload, there is a problem,
I do not really see where you can help me,
Thank...
In an answer to this question about current usage of pull-ups here , RK and Vidar comment:
Is the GPIO you have configured as a pull up, being pulled down? If so you...
How to save data persistently(non-volatile) to nRF51 core not effected by powering off and on?
(How to save static data persistently without deleted when the core is turned...
Hi,
I have just used some code from your flash_write example in the SDK, it works ok but i have a couple of issues, the code is from sdk 12.7, and the chip is an nrf51422...
I have a question about using the "Radio" peripheral on the NR51422 Dongle development ki
I am putting together a fairly simple prototype device that needs to transmit...
Hello,
I started development on a NRF52832 board couple of days ago. I want to get sensor's data via SPI (with the NRF52 as a master). However I've got weird linking issue...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hello,
on your product info page, the operating temperature range for the nrf81522 is indicated as -40..+105C, while on the datasheet the same value is -25..+75.
nrf81524...
Hey,
I`m experimenting with the blinky ble example in SDK 12.
Everything works fine with the Android nRF Blinky app.
But I noticed a weird behavior when using nRF Connect...
I have tried extracting Bluetooth address of connected device by using "ble_gap_addr_t" ,
by this i am able to get some address but that address is being changed after re...
