I am using nRF Connect SDK v2.4.0 and an nRF5340 DK set up as a PAwR advertiser. Is it possible to specify the channels to use in the Periodic Advertising train? I found the...
Hello! The PCN 219 rev 1.1 says "The new device revision of nRF54L15-CAAA is not drop-in compatible with the current revision, requiring update to PCB schematic
and layout...
Hello.
Im tring use nrf_dm sample with nRF5340 on nRF Connect SDK V2.9.0, with a custom board.
I got the error when I try dm with other device:
my prj.conf:
...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I am encountering an issue with the TWIM driver when attempting to communicate with the nPM1300 PMIC via I2C.
This problem seems to be related to the behavior of the...
I have been trying to implement a way to wake the system up after doing sys_poweroff() but no matter what nothing seems to work. I already tried many examples and none of...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,
I have a full working ble code form the example provided (keil), but I DO NOT SEE any uart interrupt happening. I can write data to the uart, but I can't see any interrupt...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I am using hw TWI with the s110_nrf51822_6.0 softdevice, nrf51_sdk_v5_2_0
I am using pin 3 scl and pin4 sda of the nrf51[48]22 eval boards.
I am able to drive these pins...
Hi all!
As we know, the funtion Nordic offer to send the ble data is called "sd_ble_gatts_hvx()". But as far as I observe, this funtion just puts the data in the stack...
Hi,
Need to talk between 2 devices using BLE, so for now I have a device with a service and advertising, but now I need the other one to work as central and connect to...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
sorry if this is a stupid question, but i'm fairly new to BLE (nRF8001), and even newer at report descriptors.
I'm trying to send some media keys, just volume up...
Hello,
if i write a new value to a characteristic with the Master Control Panel sometimes i get a HardFault failure. Most of the time all works fine, if i update the values...
I want to send 512 bytes of data over ble through the characteristic value, as maximum length of the characterstic value is 512. When I try to do the transfer more than 20...
HI,
if i want to enable only some component ex RX,TX in soft device and rest want to disable as they consume memory can it be possible?
can anyone please share information...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Might I know any programming guide for nRF51822.
The online documentation seems focus on the API instead.
I would like to know more detail on SFR (special function register...
