Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hi,
Apologies if this is an obvious question, but I haven't been able to establish from previous questions or the data sheet whether it is necessary to use an external...
I'd like to be able to change the connection interval from my central device on the fly after a BLE connection has been established between it and the peripheral. What's the...
Hi,
In the ble_app_proximity project in SDK 0.9.2, I was trying to add manufacturer data to the beacon. Here are some of the code snippets which I changed in main.c
#define...
Hello,
I am working on S120 stack with 9.0 SDK and testing with heartrate application and iPad as a peripheral. I am getting the central device as nRF51822 after central...
Do I need to implement my own timer to wrap this function? I appears that I might receive a BLE_GAP_EVT_TIMEOUT timeout event but testing has yet to reveal one.
My test...
Is there an example that is a minimal example of advertising on S110?
It might even serve one attribute that is set to a constant like '1234'.
This would help me bring...
HI
I am trying to use mkit as programmer by P20
FOR third part BLE brd
VDD---mkit.vdd
GND--mkit.gnd
SWD--P20.4
SWC--P20.5
bisides, for
P20.3(SH_VTG) connected...
We're going to be programming and debugging our prototype nRF51822 board using this adapter from Segger. It's the same connector as comes with the J-Link LITE in the dev kit...
Dear Nordic Team,
I am using Nordic DK board,
Now i want integrate UART to hid-mouse application. So that whatever data i can receive , will send to HID device without...
Hello everybody,
I'm trying to use pstorage module but it seems that the example_cb_handler function is never called when I try to store data.
I noticed similar issues...
There have been a number of other older topics with this same error message symptom, but I've tried all the solutions proposed and none have worked to solve this specific...
Hi.
I am using SD s110, ble_app_uart example from SDK10.0.0 on dk pca10028 as a peripheral. The central is a laptop running linux.
I am trying to establish a connection...
As noted here , a lower interval will give quicker connection - but at the expense of power consumption.
With a 4s interval, it seems that it is likely to take several...
Let's say I add two PPIs which both trigger off of the same event. One of these PPIs is connected to the CHG[0].EN task, and the other is connected to the CHG[0].DIS task...
In the GTT_2_Introduction nRF52 document there is a picture with text
-42 dB Selectivity (2'nd CI). As far as i concerned it's about Carrier-to-interference ratio. But what...
