Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hi,
I am using the capacitive sensing driver example given in the SDK(version 12.3) and it works fine. I want to extend the code to ensure that the SoC goes to sleep for...
I have seen exaples using the Raytec MDBT 40 with ATMEGA32U4 infact adafruit has its own board with ATmega32u4 and MDBT 40.
Can I use MDBT 40 with ATMEGA328 ?
Thanks...
Hi,
I am facing issue on nRF51 s110 buttonless DFU. We are initiating DFU using nRF Connect and the device jumps from app to bootloader. On my Android Phone using nRF Connect...
hello,
i want to ask that is there any tool for reading and writing on flash directly.
e.g tool like extreme burner .i am loking for a tool like extreme burner.for nrf51822...
hello,
i am using ble_app_uart code and in this pwm is also used but when i am enabling pwm my bluetooth connection gets disconnected.
will you please tell me how to use...
I am a student and very new with your product and how to use it.
I just order nRF52840-PDK today via online electronic store.
Please provide complete equipment list...
Hi, I want to OOB pair two equal devices (pca10040 + NFC shield) via NFC. Since its not clear which of the two devices will act as NFC initiator (active) or tag (passive)...
Hi.
I'm trying to upgrade multiactivity_beacon scanner example to SDK 11.
But, there's no config for nrf52(pca10040) in that example.
So, I configured it myself and...
Hello,
I just purchased this device:
www.aliexpress.com/.../32399375500.html
but found out that evaluation board is only a debugger and does not actually program the...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
While investigating connection parameter handling, I noticed the following:
The is_conn_params_ok(ble_gap_conn_params_t * p_conn_params) function in ble_comm_params.c only...
Hello,
I am working with S132 3.1.0 on a project based on FreeRTOS. Under some circunstances I set manually the value of some characteristics by using the function sd_ble_gatts_value_set...
Hi,
I am working with a nRF51822 board and I want to program in OTA. I know how to program over the air, but the only problem is that when I have a new unused board I need...
