Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I am currently working on a project that uses an nrf52832, SDK V11, and the S332 soft device. I am in the process of migrating to SDK 12.2.0. With the release of SDK 13, I...
Hi,
IOS example code
How to import CorePlot correctly in Xcode?
I always get this error message:
~/IOS-nRF-Toolbox-master/nRF
Toolbox/HRS/NORHRMViewController...
I am trying to use optiboot-ble with the nRF8001 and an atmega328p to allow application update over bluetooth. I have successfully compiled the bootloader and flashed it to...
Data sheets
Where is the data sheet for the
NRF51822 SoC located?
I am also looking for the ARM
Cortex-M0 data sheet, where is
this located?
I need to find...
When I try to program an example with nRF go Studio from the new SDK12 or SDK13(fresh download) I get the following error:
It does not show up if I don't program the...
Hi nordic guys,
I used the ble_app_hids_mouse demo to build my generic hid device(no mouse and keyboard) project.Now i modified the hids_init() function according my hid...
Hi !
I work for about a year with a nRF52832 custom board without problem and recently I add a bootloader (with success) on the firmware.
Now I can't connect through...
My application is based on ble_uart_app. I want to integrate the DTM so that the nRF51 will be in RF test mode when it receive command from UART. However, I found that the...
Hi all,
We're going to implement floating point agorithms on the new chip which has a FPU (cortex M4F). with the 64MHz system clock, how many flops can we have? I could not...
Hello.
I use nRF52 & mpu9250.
I want to use dmp.
But now it's not going well.
Now, there is no error,but fifo_count doesn't change after fifo_count became 512.
I...
Hi,
sometimes not always, the function peer_id_is_allocated return false and this causes an ASSERT of device, because a NRF_ERROR_INVALID_PARAM is returned by pdb_write_buf_get...
Hi,
We're using nRF51822 and in the future we'll use nRF52832.
We do use bluetooth, but as far as I know, we don't use encryption (code is based on the HRS example, and...
Is nrf52 support 3 wire spi interface? I am using AD9837 3-wire spi module act as slave and nrf52 dk act as master. I am using SCLK, SSn(i.e.,Fsync) & MOSI pins only.I want...
Hi, I’m a newbie of nRF SoC. I have a BLE gadget with nRF51822_xxAC that controls LEDs and obtains data from accelerometers through I2C(TWI) devices. The hex file for the...
Hello,
I am able to get NRFtoolbox dfu code work for iOS 10.3. and now able to perform the DFU on BLE device.
But when I perform the DFU its GAP name changes from Beam...
