Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I read timer example of SDK7.0/6.0, and found that often we write some code to tigger the clock.
but the same example of SDK9.0 needn't. why ?
the code of SDK7.0: NRF_CLOCK...
Hi,
I am developing ble apps with the BL600.
I am coding a source file with the keil IDE. And this source is deployed to the nRF51 DK board through the nRFgo Studio....
hello,
i am unable to update application or softdevice or bootloader via master control panel 3.9.0
while doing so, it shows error:"FAILED TO OPEN TRANPORT BACKEND". ...
I followed the Nordic Tutorial located here . I'm using a PCA100028 Dev Board, MCP 3.9.0.6, and a Segger J-Link Plus. I'm using Keil uVision5, and used the pack installer...
I have a set of characteristics on my ble peripheral (nrf51) which I display with nordic control panel tool (android). but when I deleted one characteristic on the peripheral...
Hi, I am evaluating the use of Gazell and BLE as a possible solution for my project. I had heard that there was a way to have both BLE and Gazell running on a device at the...
we will do some measurments and answer when we get some time to spare for this. Others are welcome to answer/comment freely about their experiences/knowledge.
I have some custom hardware (nRF51822) with a couple sensors on it and would like to have the data sent via BLE to a smartphone. This may be timer based on triggered by an...
Hi :
I want to update the firmware of 24le1 over the air ,follow the 3 step ,fail.
download "rf_adapter_nRF24LU1P.hex " to the nRF24LU1 by nrf6310,and connect to PC...
I am using the nrf52832 to communicate uart with hw flow control and a baudrate of 9600 and fifo.
Everything is going well most of the time, but sometimes the other device...
I write an infrared receive driver on example ble_app_uart with softDevice 6, but it not work after I use softDevice 8.How to fix it ? Is there an offical infrared receive...
I'm trying to generate a 1kHz PWL and call a function every 1ms the code is below.
My initial though was to set TASKS_CLEAR once the timer reached the max pwl value.
Oddly...
Hello,
I am using multilink central example to connect to multiple peripherals. But I am facing a problem in connecting 2nd device.
After connecting the 1 st device, upon...
Hi,
the S130 supports multiple connections for the Central role. Is it possible to connect to multiple devices at the same time? E.g. calling sd_ble_gap_connect() asynchronously...
