Hi Nordic Team,
I am trying to implement a secure boot chain on the nRF54L15 DK using NCS v3.4.0 (LTS) with the following configuration:
Board: nrf54l15dk/nrf54l15/cpuapp...
As in subject, psa_aead_finish function generates incorrect tag for AES-GCM when Nordic proprietary library is used.
Works fine with Oberon backend.
Similar problem reported...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hi,
My project need to transmit mass data(maybe over 64kB)to APP once.But the total transmiting time is better not over 30Min.i use your example nRF51_SDK_8.1.0_b6ed55f\examples...
With the nRF51, it was not possible to run a high frequency realtime task due to the SoftDevice running with the highest interrupt priority, is this different for the nRF52...
I'm using the Github project github.com/NordicSemiconducto.. . in order to SCAN in a specific channel rather than all 3 channels. I don't want to use the timeslot API continuously...
Dear support team,
I have some trouble with a custom board using the NRF51822.
Sometimes the MCU resets supuriously.
After reset I try to find out the reason by reading...
I am following the Makefile provided by Nordic, but using --reset with --program seems to fail:
>nrfjprog --reset --program _build/nrf51422_xxac_s110.hex
ERROR: Two arguments...
Hi,
i am using three s210 master devices to broadcast ANT messages to a s310 central device. The central connnects to a PC through USB dongle and BLE.
When broadcasting...
Hi,
I found several posts on this forum closely related to my problem, but non of this answer my needs. I try to program nRF51822AA with blinky example via Keil uVision...
Hi, in evothing and mbed all the UUID are 128bits long
however, in EK, the code use 16bit UUID
ex. nus.c the uuid is 0x0001 0x0002 0x0003
any one knows how to provide...
Hi,
I have just received my smart beacon kit (nRF51822 based), I have wired up my JLink programmer according to devzone.nordicsemi.com/.../
However I am having trouble...
Hi!
I'm building a mesh using beacons. Everything works good untill now, except beacons sometime stop advertising on its own. Beacon still works because he still connects...
Hi. We are going to mass production now and the lab that will certify our product says we need to have a special mode in the firmware that would do : modulated middle channel...
I want to make a custom board using nRF51822. Currently I am using nRF go studio starter kit and pca10005 board. I am using segger jtag programmer for loading code to the...
Hello,
I have a custom program based on the uart example. I can write to the device, but sending to the master fails.
I call the SendString code, but p_nus->is_notification_enabled...
