Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
i have RBL nrf51822 ble and i want to try it with BLE Sniffer. i flashed the nrf sniffer hex file by drag and drop to my dongle but it doesn't show anything. only it shows...
Hi Everyone,
I am working on a hobby project with nRF51822 which needs me sample upto 4 signals reliably at 500Hz each at 10bit resolution. I have read through few posts...
Hi all,
I have two nRF52 connecting, transmitting, disconnecting and sleep mode when are in normal operation, now I am experimenting a randomly error code 8 when calling...
Dear Nordic Team,
Meanwhile, I've burned through a week finding a solution for this problem.
Now I am out of ideas where to check for problems.
My application:
I...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
I'm trying to flash a nRF518122 with a St-Link V2 programmer via Open OCD.
The process seems to goes smooth, but comparing the number of written bytes to the actual HEX size...
How is BLE_CONN_HANDLE_INVALID changed in multiple services
I modified the ble_sdk_app_proximity example. I added x3 services, based on the BLE Characteristics, a beginner...
Hello
im building a project for discovering infections through temperature sensors, so im modifying the heart monitor sensor examples (central and peripheral) in the sdk...
Hi
I am developing an applicaztion with SDK 13.0.0 and S132 for nrf52832
The version of the softdevice to be used with this SDK is 4.0.2, and I need access to L2CAP layer...
First,the meizu phone can dfu successfully in the dual bank mode,
So do the 360 phone.
But in single bank DFU,this two kinds of phone failed,
So I make the programm enter...
I'm designing custom board with nrf51822 SOC & using buck-boost converter for powering nrf chip, If I don't add inductors in DCC line how it will effect my custom board. ...
Hello,
In previous version of SDK, I used to use "sd_nvic_systemreset()" function to reset nRF52, but this function disappeared in SDK12.2.0 .
The question is what the...
Hello,
I am receiving the above error on Android BLE app while connecting to my pca10040 based board, and I developed this app with nRF Toolbox as a reference.
I am...
