Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
ble_app_hrs_rscs_relay.hex the application ble_app_hrs_rscs_relay in SDK v9 can run fine,but in SDK v10.0.0 it doesnt work,even when i debug , it cannot go to main, and i...
Hi.
I have troubles.
I'm using nRF52 DK and V0.9.0.
I'm making program that does TWI communication between MPU9250 what is 9-axis sensor.
error is false every time.
...
I'm having problems getting the DFU dual bank ble s110 example to work on my target. My custom BLE app on my target is running fine, so my hardware is all good, and the DFU...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
I'm using s132_nrf52_2.0.0-7.alpha_softdevice. I've verified that the soft device is enabled.
void rdi_set_gap_parameters(void)
{
uint32_t err_code;
ble_gap_conn_params_t...
Is there are working example of FreeRTOS running on the nRF52 using the S132 SoftDevice? I am trying to get a ble_hrs example running with a updated version of the FreeRTOS...
Hi,
We have a rev3 nrf51822 system running S110 v7.3 and using SDK6.1.0. We are having trouble tracking down a ~1mA baseline current consumption when in system on/low power...
I'm struggling to understand this strange issue. I have a firmware based on S110 SD on nRf51822-QFABA0, this firmware is still based on version 7.1.0. The application is based...
I'm working on a program which sends 20 kb of data (sending 16 byte at a time) with one condition which is that indication should be enabled first. the first function checks...
Hi. i use SDK 9.0.0 and S130_1.0.0.
I want to recieve data from My peripheral S110..
First, I try to recieve data using example "ble_app_uart_c_S120-master".
I could...
Conditions in www.nordicsemi.com/.../Why-can-Master-Control-Panel-not-find-my-Master-Emulator-Dongle have been met, ie all components of PCA10031 have installed successfully...
in the answer of this question it said that :
You are also not allowed to send a new
indication until the previous one is
confirmed. This is signaled by the
reception...
I found this: github.com/.../nordic-nrf52832-gcc and tried to add it (and its dependency to the nordic-nrf52832-gcc 0.1.0 target to yotta with no luck. Is there a description...
Is there a maximum consecutive receive time similar to the maximum consecutive transmit time? I am operating in 1 Mb/s ESB mode. I am seeing the Rx get disabled approximately...
