Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi all,
I am using S130 in scanning mode and I would like to list the devices that are currently advertising by their friendly name. I have access to p_ble_evt via BLE_GAP_EVT_ADV_REPORT...
Hi,
I usually use electronics.stackexchange.com/.../15143 approach for decoupling capacitors and until now I had much better EMI performances.
I make sure that tracks...
We would like to reduce the attribute table size a little to increase free RAM. Are there any guidelines explaining how we can judge how large the table needs to be for a...
I compile SDK7.2 example hrs in "experimental_s110_with_dfu" by eclipse,
and I download softdevice & bootloader by nRFgo
then i use master control panel to DFU the hex which...
In the nordic documentation it mentioned that in the init packet we can write list of supported softdevices so that if one of that matches it will start the dfu. But in Signed...
Actually, I'm not good at using English. So I'll try to struggle to type this question...
Sorry, Last week. My boss gave me a Nordic Mouse to develop some embedded one...
Hello,
I am using nRF51822 and meet a question that in the process of bluetooth communication, I will get an instruction for external circuit to stop bluetooth function...
While both P0.00 and P0.01 has Analog Input function, initializing an AnalogIn (in mbed) with P0.00 will cause the firmware to fail to start at all; but initializing using...
Please tell me the Manufacture Part no: which is used for the 16MHz crystal in the PCA10040 DK. I found it different from the one used in PCA10028 version of the DK with just...
Please tell me the location to download the hardware files for pca10040 version of the nRF51 DK board. I could find only pca10028's hardware files in the nordic's webpage...
Hi,
I have some similar problem when trying to add the custom 128bit characteristic UUID.
The service UUID is advertised correctly but the characteristic UUID not.
...
Im using nrf51822 (16KB RAM), I'm trying to retain some data (RAM) after watchdog reset. when I load only the softdevice and my app, the RAM retention workings, but when I...
HI , ALL
i coded the uart_init in my project.
and i want to regarget the printf in my project.
so i find the retarget function is in the 'retarget.c' ,
i tried...
Hi,
We are using Softdevice S310 Version:3.0.0 and SDK:9.0.0.
My Device working on battery power. We are facing Flash write problem when my battery voltage goes to below...
