After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Can i use FDS with ble app blinky whith uses soft device s140.
I see that i am not able to use the fds library. What is the solution? I am using segger embedded studio
Hello,
I develop a project with NRF52 and I can't get notifications from iPhone. I have the nrf52DK and also created my own custom hardware (i am a hardware engineer, not...
It seems like the "A0" refers to Arduino nomenclature. If you want the NRF52 signal AIN0, you must use connector P16, the third pin, labeled P0.02, also labeled "P0.02(AREF...
How can i add more nodes server in light switch example in Mesh SDK 1.0.0?, i change #define SERVER_COUNT to 52 and work fine, but when i change it to more than 52 don´t let...
Hi,
I'm using SDK 15.0.0 and NRF52840 DK.
I want to merge couple examples from SDK in one project. As "base" example ble_app_uart was choosed (..nRF5_SDK_15.0.0_a53641a...
I am using the code below to save data from an ADC into a circular buffer.
I then want to save that buffer for retrieval later so I do:
But when I look at the debug...
hi all
Every time the serial port provision the mesh with python, when the temporary variables disappear are defined when exiting the serial port , how to improve the code...
hi,
I am currently learning to use the mpu6050 read and write code in the SDK from the nrf5_sdk_12.3.0_d7731ad to control mpu9250. The part of the gyroscope and accelerometer...
Hello,
Is it possible to program nRF51822 with nRF52DK (PCA10056) ?
Currently I am trying to program my custom beacon (nRF51822) connected via SWD P20 header. I am using...
Hi
I succeeded to run the DFU OTA process and updated only the application. Application is running OK
The problem is that after repower the application is running but...
Hello,
I am trying to add NFC wake up functionality to the project based on ble_uart_app example;
Using SDK14.2 SD132 V5,1 using DK52 development board
I have added...
Hi,
I am trying to add interruption on light switch example. So, eu studied the gpiote example from SDK14.
When I add PPI, GPIOTE and TIMER libraries, on light switch...
So I have my custom board up and running (nrf51822) pluged into the nrf51DK with RTT debug comm and uart comm working, also starting some initial experimentation.
...
Hi,
I am using ble_app_uart service in my application. In my custom board GPIO pin 8 is used for LED. But this particular GPIO is configured for UART RTS pin in ble_app_uart...
When an NUS Central has several NUS Peripherals connected, is it possible to send the same "message" to all of the connected peripherals at once?
Or do I just have to iterate...
