Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hi everyone,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
How should it be done and what do I have to...
Hello everyone.
I have both the two boards now. If I draw a PCB myself and want to use the Debug-out port to debug my PCB, what should I do? Which pin should be connected...
We have to pick a BLE very quickly , and up till now we used to work with modules which are expensive in mass but easy to work with (e.g RN4020)
I am looking for a chip...
It seems that my j-link chip on PCA10028 is dead.
I'm not sure How I can Fix it.. so I'd like to use external Debugger(?? I don't know how it called) Instead with PCA10028...
Hi,
I have seen in a few nordic videos ( devzone.nordicsemi.com/.../) , where a LCD display is interfaced with the NRF52840. I would like to know its specifications and...
Hi,
I'm designing a prototype which uses a 6V battery with nRF51822. According to the specs nRF51822 power supply ranges from 1.8V to 3.6V. Can you tell me how to reduce...
if I use softdevice 130 Enabled, then do I have any restriction with using all of the pinout of NRF51xxx?
Or if I use Nrf-51 DK, Do I have any restriction with nrf 51xxx...
I added service into ble_app_template
in static void services_init(void) {}
like this
#define NUS_BASE_UUID {{0x9E, 0xCA, 0xDC, 0x24, 0x0E, 0xE5, 0xA9, 0xE0, 0x93...
A little background and what works:
I'm already familiar with using SD110 and SD130 APIs on the nRF51 series, so thats not an issue, also it confirms that my boards...
Hi,
I'm using the SDK10 bootloader and DFU mechanism. I can update the firmware using Master Control Panel 3.10.14 on a PC, but the update fails using the iOS library or...
Hi,
I want to turn peripheral device from application mode to bootloader mode from a central device(not app), so I am trying to write value 0x01 to dfu service.
Following...
Hi,
I am trying to evaluate the NRF51822 with S110 softdevice stack. My IDE is the IAR Workbench 7.10.1 for ARM. I downloaded the most recent s110 version (s110_nrf51822_6...
