Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
According to the *.map file the .bss (RAM) usage for my Application is 0x16b8 or 5816 bytes. This is obviously a very high RAM Application, likely due to the abundance of...
Hello Nordic,
I am working on [nrf51822 custom board+SDK8.0.0+SD110]. I need to test button press bouncing and de-bouncing, how it works on the board ? I found one example...
Hi,
is it possible to use this module from LAIRD in connection to the nordic SDK - i installed the softdevice hex but the hrs example for s110 is not running properly ...
Hi.
My nRF51822-mKIT, when attached to the USB port, don't flashes the green LED nor the drive appear on Windows explorer.
It's possible that mbed loader was corrupted...
I have found that when I try and initial the Softdevice to use the Scheduler, shortly after initialization and right before dm_init() runs, I get an NRF_ERROR_NO_MEM error...
Hello,
I am trying to use nRFUart project given with the Master Emulator API, however; the original code crashes while trying to initially reset the hardware device. I...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
I'm implementing a Eddystone beacon ( github.com/.../eddystone ) with the 3 specified frames and it works quite ok with changing the advertising data before transmitting by...
Hello,
I am trying to use the new bootloader provided in SDK v6.1.0 with SD v7.1.0 and MCP v3.7.1. I have loaded the unmodified project from nrf6310/device_firmware_updates...
Hi,
In order to use new nRF51 SDK v. 5.1.0, we have just bought a new NRF51822 EV Kit from your distributor. It contains PCA10001 v2.2.0 2013.49 but the IC is nRF51822...
I am trying to pair nordic with an iPhone app. (using lightBlue) but not device_manager_evt_handler is not getting called
Here is the code, Is there anything else that...
Hi,
i need select bluetooth chipset,but it should support options below;
-Minimum baud rate should be 300 bps,
-It should support 7,8 data bits,
Which can i choose...
Hi
I try to write an application in C# with the MasterEmulator dll (Version 2.1.12.6). It works with the dongle, but not with the nRF51-DK. I can open the Device but I...
Hi,
I am planning to use nRF52832 for one of our projects. Can you please help me with the SDK that will support IAR Embedded Workbench.
Thanks & Regards, Yaron
