Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
My set Up: Nexus 6 (Android version 6.0) as Peripheral, Nordic as Central.
I want to achieve ble pairing using 'pass key confirmation' methodology.
The nordic device has...
Hi Nordic Developers..
I am using nrf52 with softdevice 132.
In my project i am using external EEPROM(Microchip 11AA010) that uses UNI/O protocol and Single I/O Serial...
I'm using SDK 8.1.0 (SoftDevice 7). I built a version of dual_bank_ble_s110. Installed both on a freshly erased pca10028. It comes up fine and sets the LED on. It's advertising...
Hi guys,
I'm facing some trouble to put my rtc working properly. I made a code based on the rtc example but it's not incrementing the time the right way.
Bellow follows...
Hey,
I have written a custom service for my company's sensor readings on the nRF51 DK, on top of the uart peripheral example given n SDK_11.0.0. However, for the final...
What should be done if we add nRF51822 SDK into our code for business (redistribution)? We have our own IDE and would like to integrate "nRF5_SDK_11.0.0_89a8197" into our...
I wanna plan to design a new hardware which has ability to connect to smartphones using BLE and broadcasting ANT pages in the same time. I also need a way to transmit some...
Hello,
I read the Errata document infocenter.nordicsemi.com/.../nRF52832_Engineering_B_Errata_v1.2.pdf , and in the section "3.10 [62] NFCT: Can draw current when not enabled...
Hello,
I'm designing a new design and planning to use WLCSP version of nRF52832.
I have few questions about this since all reference designs are made with QFN48 version...
Hi every one,
I use the nRF51822 to read temperature from sensor and send it through UART, i follow the SDK examples and just change connection interval to 0.5 sec and...
Hi I am trying to get my 128x32 oled device working with my nrf52 development kit board. Using PCA10040. Does anyone have or know of any example code that can get it up and...
Hello,
I am writing some data to flash, but when it runs to storage_clear, I get the return code---0x10. It seems clear failed. And I tried storage_update, and it failed...
Hi, I'm working on a project, I want nRF51822 can get notification when android phone got a call or email, just like ANCS work with iPhone.
I tried ble_app_alert_notification...
Hello,
Apologies as I'm very new to C and I may be missing something obvious. I have an actual ble Heart Rate device which I wish to connect to my pca10028 (nrf51422_xxAC...
