In Electrical specification Table 1 (current consumption in forced High Power mode) lists a typical value of 7.2 mA , just want to confirmed this is correct and not a typo...
Hello, I am developing my custom board using Thingy53 as a reference design. I am trying to achieve DFU from application using external flash for the secondary image and upload...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Is the nRF Temp App source code available for download?
I am currently developing an ultra-low non-connectable beacon and would like to use the nRF app as a starting point...
I guess all the Bluetooth members saw the email from the SIG about the next version of Bluetooth and how it is confirmed to have double the range, quadruple the speed and...
I'm looking at table 23.15.2 in the nRF5 Reference Manual, and it states that TX startup current is 4mA with the DC-DC enabled.
Does that 4mA include the CPU idling...
My project: nRF51422, S110, based on SDK 7.1.
My project employs several application timers (run via the scheduler) and a continuously running Timer1-based 1ms timestamp...
Hello again,
i wanna use the UART communication for transfering data from my µc to the nrf51 and vice versa.
For a test i used the ble_app_uart example and it works...
Hi,
I programmed my NRF51 to read ADC samples and I trying to transmit the information to a dongle. So far I have been able to send the hexadecimal values of the recorded...
Heyho!
Is it possible to set the PWM base clock frequency to 40kHz? If so, how? I see that the predefined base clock frequencies don't go any lower than 125kHz.
I'm...
Hello everyone, I am program for PCA10001 and I want to use Bootloader to upgrade firmware through OTA for my device. I have a old file bootloader use for s110, and I tried...
Hey,
I would like to send data from Central to Peripheral. I follow by ble_app_uart example, however I need to send a float type variable, so I split it to the total and...
I have 2 identical nrf52832 development boards with PCA10040 V1.1.0. One is running the ble_ant_app_hrm example from the nRF5_SDK_11.0.0_89a8197. This example appears to run...
Hello,
I'm developing a product using nRF51822 which is intended to work with iPhones (only iPhones for now; iPod/iPad and Android later).
I need some kind of document...
Hello,
I'm trying to recreate the PWM_library example from the v.11 SDK in a new file in Keil. I have compared the debug settings in my project to the debug settings to...
Hi there,
I am following the thread to use JlinkExe and JlinkRTTClient. I encountered a situation which i don't understand.
After running JlinkExe (go to the folder...
