Hello,
I've an issue that I can't find clear instructions for the nRF5340 serial recovery for the network core.
Being able to update both cores from the bootloader level...
Hi,
I am trying to use mcuboot to load a version that is stored in my external flash, and I cannot get it to boot. My project is being built using sysbuild and my target...
Dear Onomondo Support Team,
I am currently experiencing an issue with my Onomondo SIM card — it is unable to register on the network when used with the nRF9151 DK board...
Hi , am developing the st7789v_minimal_sample application using Nrf52840. after creating minimal application am facing some unrecognisable issue. which am stuck can you please...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
Hi,
1. It was measured that SWD0_SELECT needs to be connected to VDD to program the external nRF54L15 2. Will the document or the program be modified here to make it consistent...
In my application we have an nRF514L configured as an SPI target. Page 830 of the nRF54L datasheet (version 0.8, dated December 2024) documents that the SPIS peripheral requires...
I changed the dfu start address to 0x00 and application start address to 0x8000.
The application use the RTC0 IRQ to count the timer,
but the RTC0 IRQ did not work correct...
I've been successfully using IAR and I-jet with the 51822 and S110. I can build, download and run under the debugger with no problems.
I recently switched to the 51422...
Has anyone has any success flashing a nRF24LU+ dongle NOT using the official dev kit ? I'm attempting to flash using another microcontroller programmed as an SPI Master so...
I will be happy if someone points out this is a newbie problem and not something weirder...
Running on Win7, 64 bit BTW...
I recently received the nRF51 eval kit. I...
Hi,
I am trying to connect my msp430f1611 microcontroller with the nrf8001 bluetooth chip. I read this thread ( devzone.nordicsemi.com/.../) and it seems very helpful....
I have been trying to implement a SPI Master on the nRF51822 Eval board in order to read data from an Analog Devices ADXL345 3-axis Accelerometer. I chose to start with the...
Hello,
Firstly, the nRF5122 Product Specification v1.3 Section 4.2 says that TIMER0 is 32 bits wide.
However, other product specs seem to mention 16/24 bit timers, and...
Hello Nordic people!
I'm developing my first firmware on nRF51822 and I need help with BLE, profiles and SoftDevice S110 stack.
Application it's a speed sensor for bicycles...
I have nrf51422 dk. The boards I connect to 3.3V power and via jlink to my pc.
I use the JLink command line tool.
I can not access the chips. Erasing is not possible and...
Hi there,
I am using Eclipse and GCC (codesourcery) as development tools.
In the gcc makefile, once provided by Nordic with the "button_radio_example" are two lines...
Would the example github.com/.../require-encryption-5.1.0
compile without any extra configuration ?
I am trying to build it in a Keil uVision v.5.12.0.0, but I have some...
Hi,
I have an idea to implement BLE based access control application. I considered nRF51822 based Peripheral device & iOS application for central device
Both the Central...
We are in the process of creating our 2nd pass boards with following components to achieve good RF range>20 meters. We are considering discrete BALUN components and SMD Chip...
I see 5V pins on the schematic for the new nRF51 development kit. If I power the board via USB, I understand that 5V is regulated down to 3.3V for the chip. Is the source...
hi,
i'm gonna make 51822 enter low power consumption mode.Meanwhile it could be wake up by "GPIOTE_IRQHandler()"
1:Now,i know that "sd_power_system_off()" can make 51822...
