Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I am trying to build the mesh-bootloader and the cmake build system throws some error, could You have a look at my comandline options, or say what is going wrong.
I am using...
Hi
I want to make a dongle which can connect to and communicate with HID .if the peripheral is a HID(eg gamepad ,consumer or mouse ),the central device how to communicate...
Hi,
This is just a quick check of my understanding of the interrupt priority levels on nRF51. I read up on the documentation I can find.
I'm assuming that I will receive...
Hi,
I am designing a custom PCB with the nRF52832, I am going to use wire bent antenna over it. Can I bend feed wire by 45 degree. I have attached image for the part I am...
Hi All
I am using the example of uart in SDK10 wit nordic 51822
First of all ,I add a PA with 51822 to increase the signal of BLE, but I notice that the speed of PA is...
I can read peer address and rssi field in the scan request report. But how can I read the AdvA address field in the scan request to make sure that the scan request packet...
Is there a method to remove a node from the network using the current bt mesh stack? I've looked through device_state_manager.c but it appears to me that there are only functions...
Hi,
I am using 2 nRF52840 DK to build a network, One is the client and the other one is the server. Both of them are connected to computer with USB cable.
I would like...
hi,
i test my project for i2c sensor module, the debug found have error what there are the following error tips.
..\..\..\swct_application\i2c_sensor_driver.c(14): error...
Hi,
I'm trying to write custom boot loader, that receiving hex file via uart and write it to location 0x40000 and then jumps to the location. I changed FLASH_ADDRESS and...
Dear experts,
We are evaluating to perform Round Trip Time (RTT) measurement for ranging application. The accuracy requirement is 1m to 2m. Are there any sample applications...
Hi,
I am using a custom board which I designed based on the Puck-js board, except that I am only using an I2C based distance sensor instead of the other devices onboard...
After experiencing UART problems without handshaking I opted to enable hardware handshaking.
Where RTS & CTS are pins 5 & 7 respectively.
I was experiencing overrun (insufficient...
The nRF6905 nRFready Basic Remote is a complete hardware and software reference design for basic 2.4GHz RF remote controls.
What nRF24LE1 devices are included in the hardware...
hi sit and test bluetooth mesh and i do not quite understand how the client knows that the server is off or on and there is a way to find out if a server is on or off
