Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi guys,
I am trying to use pstorage to store a temperature data inside the ROM. I have to use it as efficiently as possible so that 20.000 erase cycles should be enough...
If I want to set transmit power to -4dB, these are the settings:
command=LE_TRANSMITTER_TEST (this wouldn't be used anyway)
freq=0x3C (meaning: -4dB)
length=2 (meaning...
Hi,
I would like to store firmware version number at a particular offset from the application start address so that it can be retrieved by boot loader as explained here...
Are there plans to release the files for download instead of online-only access through the Infocenter? It was always so nice to have them on-hand to grep in the previous...
When I try to compile DFU examples, I get the following errors :
"..\..\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production...
I have my custom board wired to the nRF52 DK. Using the SAADC example code located in GitHub I am trying to set up SAADC to measure the coin cell battery that will power the...
I am sending and receiving streams of data over BLE.
Do I need to add a checksum byte for every GATT write/notification/indication to ensure that my data is not corrupt...
Hello All,
I am interfacing nRF905 as a receiver mode which are interface with nRF51 DK.
As a transmitter used this module www.alibaba.com/.../RF-100m-transmission-distance...
Hi,
I'm facing a little problem with custom service characteristic. I've set char settings as follows
attr_char_value.init_len = sizeof(uint8_t);
attr_char_value.init_offs...
Although this is easily fixable, Nordic engineers should be made aware that they made a minor change in SDKV12 that breaks makefiles on the Mac.
In /components/toolchain...
Hi,
I have downloaded the latest SDK12 for nRF52.
And i tried out the new "BLE Secure DFU Bootloader" example.
But i found that doing the BLE DFU with nrfutil on...
Hi,
I have nrf52 DK and sdk11.
I want to implement the time using internal RTC , the clock should run if the power is off ,i'm implementing in central code ,it has to...
Hi, I'm planning to add bluetooth LE support to my Arduino based project. I want to use nrf52832, but I couldn't find any example on Arduino interaction with this radio. I...
Hello. I have the need to get a device's unique address that remains stable across device firmware upgrades, etc.
Before SDKV12 I've been using sd_ble_gap_address_get(...
