Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
I have a custom board using a nRF52840.
A part of the configuration is a Analog Devices MAX98357AEWL+T Class D amplifier which is driven by i2s0.
When the board is idle...
I am having an issue implementing a WS2812b driver for the nrf51422 using the 210 softdevice. We currently have ANT enabled with a tx master only channel setup. The WS2812b...
What I would like to do is run a basic SPI program that reads data from a register on a non Nordic transceiver chip. My nRF51 would have to act as the master because the transceiver...
Hi,
Which service should I use for temperature non-health related, like room temperature, for example? I have browsed trough the Gatt Specification>Services of the Bluetooth...
Hello,
I follow the tutorial devzone.nordicsemi.com/.../
And in the step of copy examples
I only got ble_app_uart_s130_pca10028
and no package of s110 was found
I'm...
Per my another question:
devzone.nordicsemi.com/.../
I have taken the kind advice of Bjørn Spockeli but to no avail.
I tried this solution to enter debug mode:
...
I want to use the sd_ble_gatts_hvx() to send the notification with a packet, and the length of packet is 12 bytes, but the return value is "0x000C". I tested the length and...
Hi,
I try to run a dual mode(peripheral/central) with S130. I'm using SPI serialization and sending command form an external MCU. I try to follow the example ble_app_hrs_rscs_relay...
Hii all,
I am trying to work with dfu, I developing an application that works with dfu, when I flash the softdevice and bootloader the device advertising as dfutarg and then...
I've loaded the S210_nRF51422_5.0.0 softdevice on my board from the nRFgoStudio.
I compiled the ant_hrm_tx_auto_s210_pca10028 project with no problem. However, when I try...
Hello,
I am developing two systems. One is a peripheral that advertises both a beacon and a ble peripheral custom service (using nRF51822 with s110 softdevice). The second...
Hi,
I am trying to use an nrf51822 with a sensor that outputs value between 0-5V. What I am confused about is how to read input voltage on the beacon. I saw some people...
Hi,
I need to debug my perpheral device, but as I know if I do debug when SD is running, it can cuase the time sync issue, then cause the hard-fault. I know there's a way...
hi ken：
I use Nrf52832(S132) to act as central and peripheral at the same time, which like the project ...\nRF52_SDK_0.9.0_0c82e3e\examples\ble_central_and_peripheral\experimental...
Hi,
I run ADC mudule together with SD, but go into hardfault eatch when I release the HF-clock.
Chip: 51822
SDK : 10.0-alpha
IDE : Keil-472
I use this function...
Hi!
I have inherited a large codebase that I'm trying to migrate to SDKv10 from SDKv6.
The project also uses an A4960 BLDC motor controller. To bring the motor up to...
