hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi ,
Need a bit of help here.
I am trying to use TWI and SPI in a single code for communicating with two different slave devices, the LTC2941 coulomb counter and the EM4325...
I've adapted the SPI example to read a value from an Analog Devices ADXL350 accelerometer as follows:
But when connected to the accelerometer this hangs waiting for the...
Hi, DevZone,
I am trying connect nRF52480 Preview DK and an Arduino UNO CAN Bus shield.
What I did is:
1) I directly hook CAN Bus shield on the top of nRF52480 Preview...
Hi,
Does anyone know where to download the old SDK versions? I tried to search it in Infocenter, but there I only found the manual documents and API reference, not the SDK...
How slow will an nrf52832 run, using an external crystal, for the purpose of extending battery life? Or am I looking at the wrong processor? I'm looking for a processor for...
Hi everyone!
I'm new to this platform and researching if it's right for my game studio. What I am looking for is a list of boards that have compliance, ideally in the EU...
Hello!
SDK15's DFU with app_scheduler is great!
I am able to Select, Create, and Write an Init Packet. On Execute, however, I get "Flash erase failed (0x3)". What might...
Dear All: My board will reset some time, and i print the register "RESETREAS", and It's value is 8, the PS says it is "cpu lock up detected", Could anyone tell me what will...
Continuous input of audio stream at ATX , but intermittent output audio streams at ARX. why?
how can i use data channal? Once data (three bytes) is sent at ATX,Receive data...
I try to use the SDK 11.0 for my nrf52832 dfu function . But i encountered the error as below:
I am using the ANT_s332_nrf52_5.0.0 .
Any advice . thanks
Building configuration...
Hi all,
I am using SDK14.1.0
Steps of my execution are -
1) My requirement is to make bond when making connection to the android APP. I have done following initialization...
I'm just getting started with the NRF52DK, Mbed and BLE development. I started with the BLE LED demo( https://github.com/ARMmbed/mbed-os-example-ble/tree/master/BLE_LED )...
Hi, we're developing a peripheral (SD 132) which uses whitelist to prevent connection from unwanted devices.
All works fine and when an unlisted device try to connect, it...
