I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
Hi,
I downloaded latest version of SDK and all examples resented there are for nrf51422.
Can I use those examples for nrf51822?
I'm using ukeil and I can only select nrf51422...
Our chip seems to be running at ~500uA and I'm trying to narrow it down.
I'm doing periodic battery level checks on a timer using the ADC HAL. So at init I call nrf_adc_configure...
I use s110 send notification to s120 in 1 - 1with 7.5ms connect interval,but the data maximum data throughput is only 21.3 /2 kbps.how can i do to raise the throughput???...
i use s110 send notification to s120,and set connect interval with 7.5ms,but in actually the connect interval is 15ms!!I see s120 softdevice specification,s120 as client which...
Hi,here i met an issue that when i set address type in public mode by funtion sd_ble_gap_address_set(),and then the advdata packet data was all zereo.This project was created...
Dear ladies and gentlemen,
There is not much information about the RESET pin in the datasheet. I guess, it doesn't have an internal pull-down resistor, but when I look at...
Hi,
I have a problem configuring readback protection using boot.
It seams that the BOOTLOADER stops when trying to read some information from the softdevice if readback...
HI:
i want to use peripheral and central function.and i can switch it to work peripheral or central state when i need.which stack should i use.s120 or s130.
I am using CMSIS RTOS (RTX) to implement an application for the NRF52 DK. I have found an error in the SVC handler that results in a hard fault when calling a soft device...
Hi all,
I was trying to use the S130 Softdevice but the uart peripheral doesn't work properly... I am trying to send three bytes, but only one appears. Flow Control doesn...
I am using a mutex to protect a serial debug printout.
Is it safe to use sd_mutex_acquire in a blocking manner, provided it is only called from main and softdevice callbacks...
As suggested in another post , I asked to our Nordic dealer about nRF52832 chip availability.
Thay talk about 2015 december for mass production , as your direct info confirm...
When i setup DEVICE_MANAGER_MAX_BONDS in 2 and trying to connect third device the nRF 51422 (10028) is freezing and all LED's light up. Why the algorithm in "device_manager_evt_handler...
Hi
I managed to integrate the buttonless DFU example, but while testing it, I have a few difficulties.
I use Lightblue to access my services and enable notifications...
