I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
hi , now I am using nrf52832 base on the sdk 14 to develop our location system, the ibeacon around my nrf52832 circuit board will advertise every 500ms, and the parameters...
My device is entering DFU mode, staying there for a few seconds, then shutting down. I'm trying to figure out a good way to figure out if it's a watchdog issue or a power...
Hi.. I am still new in using nrf product and understanding the example given via SDK. For my project, I am trying to send continous data via BLE app UART to mobile phone....
Hi,
As a part of settings up an automatic BLE DFU testing environment, we're trying to update a single NRF52 board using a PC connected to a NRF51 dongle.
The dongle is...
Hi,
I am using Sunding-515 cycling speed and cadence sensor it’s data is broadcasted as per the GATT characteristics. We have already done the data parsing in our other...
In SDK 15.0.0\modules\nrfx\soc\nrfx_irqs_nrf52810.h, at line 65,( link ) it defines a SPI1 compenent:
But 52810 spec( link ) mentions only SPI0.
Is the code file correct...
Hello everyone,
So I'm trying to maybe start get going with the NRF52832 platform but every time I try I get stuck with it.
In this example I'd like to use different...
Hello, I would like to know if there is there a "global" sdk_config.h file which has #defines for all modules? Ie, if I make my own project, and use this file, all I would...
Hi!
I would like create my own application of BLE Mesh on nRF52832, I had gone through the Light switch example and understood some basic concepts and now i'm thinking start...
Hi,
I tried to erase the bound and start another pairing procedure without rebooting my device. I was not able to remove the bond correctly. The system hangs when I call...
Hi,
I had Completed secure OTA in my custom board (RL nRf51822 A1).
We have to PCBs. 1). Old Design 2). New Design
1). Old Design: We have connected relay on pin(p6...
Hi all,
In our program calling app_usbd_cdc_acm_write() a single time does not directly send a message to the terminal program (Teraterm). Even Teraterm is not getting connected...
hi, everyone:
I want to use the experimental_bootloader_secure_serial to update firmware with UART, disable the hardware flow control.
how to reset system when application...
Hello,I have couple of nRF52832 boards,nrf5_SDK_for_Mesh_v0.9.2-Alpha.
I want to test the light control example,but some problem bother me.
It can not work normaly.The...
