Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
How do I maximize range for BT5?
I have two nRF52840 pdk units and I have loaded the ble_app_att_mtu_throughput app and tried it out. I have been seeing around 70 meters...
Hi. I tri to use my soft i2c lib
It works well at nrf51 and other mcu's. But nrf52 i2c_read doesnt works properly.
Other funcs works well.
When i read byte from i2c slave...
Hello
in the zephyr 1.7 release there have NRF52 and NRF51 porting without softdevice .
in the SDK 13 ,there has Freertos example working softdevice ,is there any plan...
hello friends :)
i'm trying to make an nRf51822 evaluation board for breadboard
i used 0.1" header and power from usb connector
i'll upload my altium schematic and...
Hi,
We are doing DFU updates through a nrf51422 dongle (data passing from UART to BLE), using our own code, based on the multilink central example.
The DFU peripherals...
Hi, I'm have a question :
If i download s120 or s130 softdevice, which SDK version i need to download ?
Which version is compatible with my nrf51822xaa ?
The reason is...
Our BLE hardware is designed to send data at 50 Hz speed continuously using nrf51822.
It worked well with APP with Android 4.3 and some Android 5.0/6.0 ,we can receive data...
Hi,
I'm getting familiar with my nRF52 DK (PCA 10040).
I stumbled on something when I was doing an application that toggles LED1 on every TIMER0 event (200ms). Here...
Hi,
Id like to understand the FDS state after flashing the device. Im trying to check if the record exists then I use it, otherwise I write a valid info into the record....
Hello All
Could you please guide me. i want implement BLE with SPI interface...if i sent any command via mobile Bluetooth..then NRF51 DK should receive the Command and...
I have already changed the define NRF52, NRF52832_XXAA,BOARD_PCA10040 to NRF51,NRF51822 and BOARD_PCA10001 and adjusted the ROM and RAM areas as below.
But there...
ERROR OCCURS WHEN TESTING UART nus service on a nrf52832 custom board UART APP SHOWS LIKE THIS device doesn't support UART WHEN I TRYING TO CONNECT WITH MY DEVICE. PLZZ H...
Hi Nordic Team,
In one of our application, we need to interface BT HCI chip with Host MCU(Cortex M4 based). Below are the application profiles we need support for:
...
