Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I sniffer the packets when I use a phone to connect to a BLE device.
However, in the packet with CONNECT_REQ label, the source address (init address) is not the bluetooth...
Hi.
I'm trying to communicate with legacy nRF24L01P using nrf51822.
I received packet from nrf24l01p, but I can't send information back.
The data I should send is more...
I use the persistent storage manager for saving some calibration parameters. It seems to work ok - I can power off/on, and the values are still there.
However, after I...
Hi. I would like to get into bare metal programming, and have decided to go for ARM processors. Are there any ns-kits or courses availible for purchase?
thnx in advance...
I have a few questions regarding power-fail comparator (POF).
How much current POF consumes? About the same as low power comparator (0.5uA) or lower?
How will softdevice...
Hi,
my firmware works fine, but when I tried to do DFU using the master control apk, it would get to the download screen and then quit.
This is the text:
DFU version...
I wonder if I can ask about the leds intensity control:
I need to control the led intensity without the PWM because I'm using the softdevice & PWM didn't work with it,...
Dear All,
I'm trying to set a static passkey. I have created 2 custom characterestic. One characterestic is used for notifications and the other one for writing. For communication...
I'm making a peripheral device that should be powered off most of the time, but never idle if on, so I want to make sure that it is always (1) connected, or (2) advertising...
Now I have a project to build the schematic.
a, 5 LED indicators(0603) were driven individually by GPIO port directly, serial with resistor, then pull down to GND.
Is...
I installed nRFgo Studio Version 1.20.0.2 (which removed my older version) and was trying to program a softdevice (5.2.1) into our custom board and was presented with a popup...
Hello, I just received the nRF8002 development Kit and want to connect it to my windows 8.1 64bit machine. I get errors that there is no driver. Tried downloading the latest...
Hi, when calling sd_ble_gap_address_get from APP i get 0xXXXXXXXX4F and when i call it from DFU i get 0xXXXXXXXX50(X beeing the same), why is this? Is it a feature or a bug...
Hey Nordic--
I updated my Keil project from SDK v8.0.0 to v8.1.0 and immediately get some compilation errors due to redefinition of symbols.
In nrf_sd_def.h, I think...
