Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
Hi,
I am using nRF52 chip with SDK13.0. MTU size 155.
I am connect with device using android phone. After sending 1 byte command device starting to send continuous notification...
hello there i think i need two uart in my application. i read datasheet of both nrf51 and nrf52
in both there is only one uart.
can anyone have implemented software uart...
Use this routine E:\nordic\nRF5_SDK_12.2.0_f012efa3\examples\proprietary_rf\gzll\experimental\gzp_desktop_emulator
To modify the can communicate with PC nrf24luep pairing...
Hi.
I'm troubled.
I use nRF52 preview DK v0.9.0 & Keil5.
i tried ble_app_hrs_c in example folder of nRF52_SDK.
This program stopped at
err_code = sd_softdevice_enable...
Hello all,
I am actually implementing an SPI-master driver in non blocking mode, I write the following code, when I use a debeug led, the program enters well in the IRQ...
I started with the blu_app_template on a 52840. I have advertising working. I can see that from an iOS app. I can also see the details of the service. I see the characteristic...
I am using the Master Emulator C# examples to build my own application. None of the examples are able to properly connect to a remote device. When I open up the Master Control...
I'm writing an nRF52 DK btle application using SDK 12. The DK comunicates with 2 external peripheral via SPI and I2C interfaces. Complilation fails with the error:
._build...
hi, i am reading mpu6050 with nrf51822. every now and then the data got corrupt because of softDevice interrupts. if i don't use Softdevice the it runs perfectly but when...
Hi All,
I am using UART with baud rate 4800, with even parity and 1 stop bit. I'm getting 6-8 bytes in a packet. I'm receiving packets for every 8-10ms continuously. This...
I am attempting to use Unity + CMock onboard the nrf51 for unit testing. I have Unity working and can even output the results of unit tests using Segger RTT libraries. There...
When I try to install nrf5X command line tools in Windows 10, I get the error mentioned in the title, even though I am not doing installing any software in parallel.
Error...
I am attempting to use TIMER4 on an nRF53832 using SDK 12.2.0 but I seem to be running into some sort of granularity issue.
Specifically, if set up the timer with 16MHz...
I just received my new NRF52480 PDK, but it will not respond to any commands.
I tried nrfjprog -e -f nrf52 and this is the log output:
-----------------------------...
Working with nRF52832 and SD132-v2.0.1
Using external 32.768kHz xtal in addition to 32MHz xtal.
I realize there are a lot of posts about timers, but I didn't find any...
