Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
Hi all,
I measured the delays between a GPIOTE event and a Task (in this case toggling with another GPIOTE) through PPI.
The results are showed below:
For the...
Hello, I followed from the link . I successfully program bootloader, and bootloader setting and program. And my program is working fine.
But I cannnot update from DFU. Everytime...
Hi,
I am working on with nrf52 with SD132 v2 SDK11 since we need serial bootloader.
I tried a gattc long write sequence to write 22 bytes. Everything works well, peer...
OpenThread recently merged a DNS client into the main branch. DNS would be extraordinarily useful because my code accesses content behind load-balancing servers with dynamics...
In this example code:
nRF5_SDK_13.0.0_04a0bfd/examples/ble_peripheral/ble_app_proximity/main.c
Where the ADC is configured to read the battery voltage:
nrf_saadc_channel_config_t...
Hi,
I've read a couple of threads in this forum that suggested that the DEVICE_MANAGER_APP_CONTEXT_SIZE value (which should be a multiple of 4) is supposed to be 16 bytes...
We're using the nrf51 with the RFAxis (now Skyworks) 2401C amplifier, which is a fixed gain 20dBm amplifier. The goal is to have a longer range 'beacon' type product and the...
What would be the best BLE Library or Framework for Raspberry-pi to exchange with nordic?
I'm trying to get data from the NRF51's GATT data.
But there are no reference...
I recently was trying to test my nrf52 DK. After lot of failed attempts i was able to do DFU update over BLE and also Serial upload .
I am now trying to test the BLE UART...
Hi
According to previous answers ( 1 & 2 ), the limitation on the maximum number of devices that can be added to a whitelist is 8, and is due to softdevice timing limitations...
I have downloaded the nRF51 SDK from here www.nordicsemi.com/.../nRF51822 and I'm trying to run HCI-UART examples as explained here developer.nordicsemi.com/.../a00063.html...
Hello,
I use SDK 13 on nRF52832 with a SD card (nRF port of fatfs lib).
I have a long sleep and i want to minimise current.
With SD card, it's okay i switch off SD...
Originally, this was a complaint about SIGTRAP 0xffffffe while using GDB.
But I've discovered the actual issue is related to a lack of erase/programming of FLASH.
My environment...
I would like to know how long is the minimum pulse width for SENSE to trigger GPIOTE Interrupt from external pins on NRF52832,I have seen
devzone.nordicsemi.com/.../
How...
